HP Workstation x1100 hp workstation x1100 - technical reference guide - Page 148

Screen Is Blank Because The System Failed To Boot

Page 148 highlights

Troubleshooting Your Workstation Screen Is Blank Because The System Failed To Boot Figure 7-1 Screen Is Blank Because The System Failed To Boot Your workstation's operating system will fail to boot if the line voltage switch is set to 230V and AC line voltage is 115V. To solve this problem: 1. Place the workstation so that you are looking at the back of it. 2. Use a small thin bladed screwdriver to slide the workstation's line voltage switch to the left until you see 115 in the right opening of the switch. See Figure 7-1. Setting the Workstation's Line Voltage Switch Slide switch to left to get 115V Slide switch to right to get 230V CAUTION Line Voltage Switch Power Plug Connector Care must be taken to ensure that the line voltage switch is set correctly. Failure to do this could destroy the power supply if the line voltage switch is set to 115V and AC line voltage is 230V. 148 Chapter 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166

Troubleshooting Your Workstation
Screen Is Blank Because The System Failed To Boot
Chapter 7
148
Screen Is Blank Because The System Failed To Boot
Your workstation’s operating system will fail to boot if the line voltage switch is set to
230V and AC line voltage is 115V.
To solve this problem:
1. Place the workstation so that you are looking at the back of it.
2. Use a small thin bladed screwdriver to slide the workstation’s line voltage switch to
the left until you see 115 in the right opening of the switch. See Figure 7-1.
Figure 7-1
Setting the Workstation’s Line Voltage Switch
CAUTION
Care must be taken to ensure that the line voltage switch is set correctly. Failure to do
this could destroy the power supply if the line voltage switch is set to 115V and AC line
voltage is 230V.
Power Plug
Connector
Line
Voltage
Switch
Slide switch to right to get 230V
Slide switch to left to get 115V