HP XM600 hp kayak xm600 series 2, troubleshooting guide for desktop models - Page 14

Case 4 — Boot Process Fails and Error Message Displayed on Screen, Error Message Utility (EMU)

Get HP XM600 - Kayak - 128 MB RAM PDF manuals and user guides View all HP XM600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Case 4 - Boot Process Fails and Error Message Displayed on Screen Case 4 - Boot Process Fails and Error Message Displayed on Screen When the power button is pressed, the PC Workstation starts to boot and there is activity on the monitor, but the boot process then fails with an error message. Status LED flashes red. A beep code may be emitted. A configuration error has been detected. • Boot process fails with an error message. • Status LED is RED. NOTE Before removing the cover, switch off the display and PC Workstation by pressing the power-off button for five or six seconds. Disconnect the power cord and any accessory cables. When checks have been completed, close the PC Workstation and reconnect the power cord and accessory cables. Verify that the PC Workstation boots correctly. Error Message Utility (EMU) In the event of an error generated in POST (Power-On-Self-Test) during the boot process, there are two beeps, then the Error Setup Manager gives access to one or more detected errors. Each EMU error is displayed as a 4-digit code with an associated text message on the monitor screen. Further details can be accessed by pressing ENTER. A detailed description of the reason for the failure and how to solve the problem is displayed. The following examples give the different types of error categories. Category #1: ERROR 0070 If an error can be bypassed with or solved through Setup, the POST should prompt: CPU Terminator Card Error Press to view more information about error , 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Case 4 — Boot Process Fails and Error Message Displayed on Screen
14
Case 4 — Boot Process Fails and Error Message
Displayed on Screen
When the power button is pressed, the PC Workstation starts to boot
and there is activity on the monitor, but the boot process then fails with
an error message. Status LED flashes red. A beep code may be emitted.
A configuration error has been detected.
•
Boot process fails with an error message.
•
Status LED is
R
ED
.
NOTE
Before removing the cover, switch off the display and PC Workstation by pressing the
power-off button for five or six seconds. Disconnect the power cord and any accessory
cables. When checks have been completed, close the PC Workstation and reconnect
the power cord and accessory cables. Verify that the PC Workstation boots correctly.
Error Message Utility (EMU)
In the event of an error generated in POST (Power-On-Self-Test)
during the boot process, there are two beeps, then the Error Setup
Manager gives access to one or more detected errors. Each EMU error
is displayed as a 4-digit code with an associated text message on the
monitor screen.
Further details can be accessed by pressing ENTER. A detailed
description of the reason for the failure and how to solve the problem is
displayed. The following examples give the different types of error
categories.
Category #1:
If an error can be bypassed with <F1> or solved through Setup, the POST should prompt:
ERROR
0070
CPU Terminator Card Error
Press <Enter> to view more information about error
<F1= Continue>, <F2= Setup>