HP Z200 HP SATA/SAS Hard Drive and Solid State Drive Installation
HP Z200 - Small Form Factor Workstation Manual
View all HP Z200 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Z200 manual content summary:
- HP Z200 | HP SATA/SAS Hard Drive and Solid State Drive Installation - Page 1
included with SAS hard drives) ● Four 6-32 guide screws ● Installation instructions (this document) ● Warranty information Tools computer or workstation, view QuickSpecs at http://www.hp.com/go/productbulletin. © 2006-2010 Hewlett-Packard Development Company, L.P. Microsoft, Windows, XP , and Windows - HP Z200 | HP SATA/SAS Hard Drive and Solid State Drive Installation - Page 2
at all times. - Disconnect power from the equipment by unplugging the power cord from the electrical outlet. WARNING! To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper computer setup, posture, health, and work habits for computer users, and provides important - HP Z200 | HP SATA/SAS Hard Drive and Solid State Drive Installation - Page 3
illustrations are examples only. Accessing the internal components of the computer 1. If you need help preparing the computer for this installation, consult the removal and replacement procedures in the service guide for your computer at http://www.hp.com/support/ manuals. 2. Power down the computer - HP Z200 | HP SATA/SAS Hard Drive and Solid State Drive Installation - Page 4
b. Position the hard drive with the connectors on the back of the drive facing upward. c. Separate the rails at (1), carefully seating the pins in the small holes on the drive. d. Separate the rails at the top (2). e. Pivot the drive into the carrier (3), and snap the pins on the rails securely into - HP Z200 | HP SATA/SAS Hard Drive and Solid State Drive Installation - Page 5
power and data connections are not required. ● The blind-mate data cables might require adjustment at the system board, based on the computer drive configuration workstations with both SATA and SAS connectors on the system board are factory-configured (2). c. Align the four carrier pins with the - HP Z200 | HP SATA/SAS Hard Drive and Solid State Drive Installation - Page 6
power and data cables on page 7. Computers that use guide screws installed in the hard drive NOTE: In some computers, such as the HP Z200 SFF, you may need to temporarily remove the optical drive to install the hard drive. See the service guide for your computer at http://www.hp.com/ support/manuals - HP Z200 | HP SATA/SAS Hard Drive and Solid State Drive Installation - Page 7
Select the SATA interconnect cable from the kit that best fits the hardware configuration of your SATA or SAS hard drive. A cable with a right- service label, located inside the computer side access panel. 3. Connect the power cable (1) and data cable (2) to the hard drive. CAUTION: Connect the power - HP Z200 | HP SATA/SAS Hard Drive and Solid State Drive Installation - Page 8
1. Reinstall the card support, if applicable. 2. Reinstall the side access panel. 3. Reconnect power to the computer and all external devices. 4. Restore power to the computer and all external devices. Step 5-Configuring the computer When powering up the computer after installation, a new hard
HP SATA/SAS hard drive and Solid State
Drive installation
This document describes how to install Serial ATA (SATA) and Serial Attached SCSI (SAS) hard
drives or Solid State Drives (SSD) in an internal hard drive bay. Throughout this document, all
references to hard drives include solid state drives.
Kit contents
●
A SATA or SAS hard drive or Solid State Drive (SSD)
●
Multiple SATA interface cables (each of a different length and with different connector orientation
combinations)
●
SAS-to-SATA interface adapter (included with SAS hard drives)
●
Four 6-32 guide screws
●
Installation instructions (this document)
●
Warranty information
Tools required
The following may be required to install the hard drive:
●
T-15 Torx screwdriver or flat-bladed screwdriver
Your responsibilities
You are responsible for determining whether the product is appropriate for your use and will interface
with other equipment without malfunction or damage. You are also responsible for backing up data
before installing any product and for regularly backing up data after installing the product. HP is not
liable for any damage to equipment or data loss resulting from the use of any product. To determine
the compatibility of this product with your computer or workstation, view
QuickSpecs
at
go/productbulletin
.
© 2006–2010 Hewlett-Packard Development Company, L.P. Microsoft,
Windows, XP , and Windows Vista are U.S. registered trademarks of Microsoft
Corporation. Printed in the U.S.
ENWW
Kit contents
1