HP rp5400 Carrier Grade Addendum - rp5400 Series of Servers - Page 46

Installing a Power Supply, Step 5., Close the one piece front Bezel., CAUTION

Get HP rp5400 PDF manuals and user guides View all HP rp5400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Removal and Replace Procedures Removing and Replacing Hotswap DC Power Supplies Figure 2-3 Installing a Power Supply NOTE If the system has a one piece bezel, perform step 5. If the system has a two piece bezel, perform step 6. Step 5. Close the one piece front Bezel. Step 6. Install the two piece front Bezel. 1. Swing the Disk Media access door open so that the plastic pins that go into the metal clips on the Disk Media bay are exposed. CAUTION The plastic pins holding the bezel on the right side are inserted into metal clips on the Disk Media bay. DO NOT bend the plastic pins or they will break off. 2. Holding the bezel with both hands, align the bezel pins with the metal clips on the Disk Media bay and carefully slide the bezel pins into the clips. 3. Attach the left side of the bezel to the server chassis by aligning the bezel pins with the chassis clips and press the bezel into the chassis until the pins snap into the clips. The illustration below shows the front bezel with locations of bezel pins and chassis clips. 4. Swing the Disk Media access door closed and attach to the right side of the server chassis. 5. Secure the bezel by wrapping the bezel strap around the bezel to prevent the bezel doors from opening. Make sure the bezel strap pull tab is visible. 34 Chapter 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
Chapter 2
Removal and Replace Procedures
Removing and Replacing Hotswap DC Power Supplies
34
Figure 2-3
Installing a Power Supply
NOTE
If the system has a one piece bezel, perform step 5. If the system has a two piece bezel, perform
step 6.
Step 5.
Close the one piece front Bezel.
Step 6.
Install the two piece front Bezel.
1.
Swing the Disk Media access door open so that the plastic pins that go into the metal clips on the
Disk Media bay are exposed.
CAUTION
The plastic pins holding the bezel on the right side are inserted into metal clips on the Disk
Media bay. DO NOT bend the plastic pins or they will break off.
2.
Holding the bezel with both hands, align the bezel pins with the metal clips on the Disk Media
bay and carefully slide the bezel pins into the clips.
3.
Attach the left side of the bezel to the server chassis by aligning the bezel pins with the chassis
clips and press the bezel into the chassis until the pins snap into the clips. The illustration
below shows the front bezel with locations of bezel pins and chassis clips.
4.
Swing the Disk Media access door closed and attach to the right side of the server chassis.
5.
Secure the bezel by wrapping the bezel strap around the bezel to prevent the bezel doors from
opening. Make sure the bezel strap pull tab is visible.