Hitachi DZMV750MA Owners Guide - Page 47

Note: • If the cover of disc insertion block is open, the ACCESS/PC indicator will blink when an image is displayed on the LCD monitor screen: In this case, the DVD video camera/recorder will not turn off even if the power switch is set to "OFF". If the cover remains open after a while, the DVD video camera/recorder will automatically turn off. • Disc cannot be inserted or removed unless a charged battery or AC adapter/charger is connected to the DVD video camera/recorder. • If a discharged battery is used, the disc cannot be inserted or removed: Connect a charged battery or AC adapter/charger to the DVD video camera/recorder. • If there is some delay before recording starts, refer to "Check 4" on page 169. • If the disc is not correctly attached to the turntable, it will be difficult to close the cover: If this happens, do not forcibly close the cover (this could cause a fault), but re-attach the disc to the turntable correctly. • If a single-sided disc is inserted into DVD video camera/recorder with the printed label facing the inside, an error message will appear. Remove the disc and reinsert it with its recording side facing the inside. See "Trouble Messages" on page 171. • When using double-sided disc Recording is possible on both sides of double-sided disc. However, when recording or playback on one side is finished, recording or playback will not move automatically to the other side. Remove the disc once from the DVD video camera/recorder, turn over the disc and insert it again for continued use. The recording surfaces of double-sided disc are likely to become dirtied or scratched: Always make sure that there is no dirt or scratch on the recording surface facing the pickup lens, and then use the disc taking great care that it is not dirtied or scratched. Use the provided disc cleaning cloth to wipe off any dirt on disc (see page 27). ●When using brand-new DVD-RW/DVD-R disc Recognition of the disc will start. F o rma t D i s c 3 Confirm the message, and then press the A button. The messages on the right will appear in sequence by pressing the A button between messages. Disc is not formatted. If it formats, it becomes possible to use for camera. NEXT CANCEL Note: • Once a disc is formatted, no data can be recorded on that disc from a PC (see Note on this page). • See page 94 for video mode. When recording on this DVD video • See page 95 for 16:9 mode. camera/recorder: When recording data from PC: 1 Confirm the following message on screen, and then press the A button. F o rma t D i s c Howe ve r , when you r e c o r d f r om PC connec t i on terminal, please do not format. NEXT CANCEL 2 When using DVD-RW, choose the recording format (VR or VF mode), and then press the A button. While the above messages are being displayed, press the C button, or when message "Format the disc now?" appears, choose "NO" and then press the A button. However, if data from PC has not yet been recorded, the disc can be made usable on this DVD video camera/recorder. When inserting the disc into this DVD video camera/recorder, the same message will appear: If you wish to use it on this DVD video camera/recorder, choose "YES". When using DVD-R, choose "YES" and then press the A button. F o rma t D i s c A l l data wi l l be deleted. Se l ec t r eco r d f o rma t. VR Mo d e VF Mode ENTER F o rma t D i s c Format the disc now? YES NO ENTER Note: • Do not initialize a disc on which you wish to record data created using the application (DVDfunSTUDIO) of PC. • When recording on DVD-RW that has been initialized from application (DVDfunSTUDIO) of PC, perform deletion using the application (DVDfunSTUDIO). (See "REUSING A RECORDED DVD-RW" on page 159) (When using DVD-RW) (When using DVD-R) The disc will be formatted. When formatting is finished, message "DVDRW(VF)/R disc, Video mode and 16:9 mode cannot be changed" will appear. 47 English