Hoover F5914 900 Product Manual - Page 16

After Using Tool, After Cleaning - manual for

Get Hoover F5914 900 - SteamVac With Clean Surge PDF manuals and user guides
UPC - 073502025550
View all Hoover F5914 900 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

After using tool (Available on select models only) Drain suction hose by turning carpet cleaner ON and holding end of hose up for several seconds. Do not press trigger. Disconnect carpet cleaner from electrical outlet. 4.13 Drain solution tube by placing round end in sink and raising nozzle above your head. Press the trigger. Proceed with steps in "After cleaning" section of manual. 4.14 Occasionally, debris may become lodged inside of the hose at the converter end (L). To clean out the hose, lift bottom of converter clip (M) with a screwdriver and remove clip. Remove debris as shown. 4.15 Snap clip back into position making sure solution hose (N) is not pinched and moves freely. 4.16 Replace Dirty Water Tank front panel (O). Rotate panel upward then push down until it snaps firmly in place. For full suction it is important that the front panel is properly secured before cleaning floor. 4.17 If the front panel is accidentally removed from the tank, it can be easily re-attached. Slide the panel into the channels (P) and firmly push down until panel snaps into place. 4.13 4.15 4.17 4.14 L M 43.1260 O N O P After cleaning Allow carpet or upholstery to dry. To help prevent matting and resoiling the carpet, keep children and pets away from surface until it is completely dry. If it is necessary to walk on damp carpet, place towels or white cloths on the traffic areas. If furniture must be replaced before the carpet is dry, use plastic or aluminum foil pads under legs of furniture so metal slides or wood finishes will not stain the carpet. If desired, the carpet may be rinsed. Rinsing is not necessary for cleaning, but it may improve the surface's appearance after it is dry. 4.18 Empty tanks, rinse with clear water and let air dry. Rinse the Clean Water Solution Tank cap and Dirty Water Tank lid and let air dry. Remove debris from Dirty Water Tank filter and rinse with clean water. IMPORTANT If the filter must be removed for cleaning, it is easier to replace if the filter is wet. Vacuum thoroughly after carpet has completely dried. This will help reduce any shading left by the carpet cleaner's brushes. 4.18 Actual model may vary from images shown. 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
16
Drain suction hose by turning carpet cleaner ON
and holding end of hose up for several seconds. Do
not press trigger.
Disconnect carpet cleaner from electrical
outlet.
4.13 Drain solution tube by placing round end in
sink and raising nozzle above your head. Press
the trigger.
Proceed with steps in “After cleaning” section of
manual.
4.14 Occasionally, debris may become lodged
inside of the hose at the converter end (L). To clean
out the hose, lift bottom of converter clip (M) with
a screwdriver and remove clip. Remove debris as
shown.
4.15 Snap clip back into position making sure
solution hose (N) is not pinched and moves freely.
4.16 Replace Dirty Water Tank front panel (O).
Rotate panel upward then push down until it snaps
firmly in place. For full suction it is important that
the front panel is properly secured before cleaning
floor.
4.17 If the front panel is accidentally removed from
the tank, it can be easily re-attached. Slide the
panel into the channels (P) and firmly push down
until panel snaps into place.
4.13
AFTER USING TOOL
4.14
L
M
4.15
N
O
4.16
O
4.17
P
AFTER CLEANING
Allow carpet or upholstery to dry. To help prevent matting and resoiling the
carpet, keep children and pets away from surface until it is completely dry.
If it is necessary to walk on damp carpet, place towels or white cloths on the
traffic areas.
If furniture must be replaced before the carpet is dry, use plastic or aluminum
foil pads under legs of furniture so metal slides or wood finishes will not stain
the carpet.
If desired, the carpet may be rinsed. Rinsing is not necessary for cleaning, but
it may improve the surface’s appearance after it is dry.
4.18 Empty tanks, rinse with clear water and let air dry. Rinse the Clean Water
Solution Tank cap and Dirty Water Tank lid and let air dry.
Remove debris from Dirty Water Tank filter and rinse with clean water.
Vacuum thoroughly after carpet has completely dried. This will help reduce any
shading left by the carpet cleaner’s brushes.
4.18
IMPORTANT
If the filter must be removed for cleaning, it is easier to replace if the
filter is wet.
Actual model may vary from images shown.
(Available on select models only)