Hoover Power Scrub Deluxe Product Manual - Page 29

Cleaning Upholstery

Get Hoover Power Scrub Deluxe PDF manuals and user guides View all Hoover Power Scrub Deluxe manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

CLEANING UPHOLSTERY Read "Before You Begin Cleaning" instructions. Be sure to check Hoover Cleaning Guide on page 10 and the cleaning code on your upholstery. Use your cleaner only on upholstery marked "W" or "W/S". 1. Attach hose and solution tube as instructed. 2. Place handle in upright position. SpinScrub brushes will not rotate while handle is in upright position. 3. Fill Clean Water Tank according to instructions on (Pg. 8). 4. Fill solution container with HOOVER® solution according to instructions on (Pg. 8). Do not use hard floor cleaning solution when cleaning upholstery. 5. Attach tool to end of hose. 6. Dry hands and plug cleaner into a properly grounded outlet. 7. Set Wash/Rinse Selector to WASH. Turn cleaner ON. 8. Gently press the tool onto the fabric. Press the trigger and slowly pull the nozzle over the fabric (Fig. 40). 9. Overlap strokes by 1/2 inch to help prevent streaking. 10. Make additional strokes without pressing the trigger to remove more solution. To clean in corners or creases, lift the tool one half inch from the fabric and press the solution trigger. 11. For heavily soiled areas, it may be necessary to repeat the cleaning process. Make crisscrossing strokes to the original pattern; overlap each pass (Fig. 41). Make no more than 2 passes with the solution over any one area to prevent over-wetting and damage to fabric. 12. If you would like to rinse the carpet with water only, set Wash/Rinse Setting switch to RINSE (Fig. 42). For best cleaning results, Hoover recommends to rinse the carpet with water only. This will remove residual carpet cleaning solution from your carpets. Then set Wash/ Rinse Selector to rinse and repeat steps 7 and 8. 40 41 42 If additional cleaning is necessary, wait until the upholstery is completely dry before using the tool again. Empty Dirty Water Tank when the motor sound becomes higher pitched and there is a loss in suction (see "Automatic Shut-Off"). When finished cleaning, follow "After Cleaning" and "After Using Tool" instructions. Actual model may vary from images shown. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
15
Actual model may vary from images shown.
CLEANING UPHOLSTERY
Read “Before You Begin Cleaning” instructions.
Be sure to check Hoover Cleaning Guide on page
10 and the cleaning code on your upholstery. Use
your cleaner only on upholstery marked “W” or
“W/S”.
1. Attach hose and solution tube as instructed.
2. Place handle in upright position. SpinScrub
brushes will not rotate while handle is in upright
position.
3. Fill Clean Water Tank according to instructions
on (Pg. 8).
4. Fill
solution
container
with
HOOVER
®
solution according to instructions on (Pg. 8).
Do not use hard floor cleaning solution when
cleaning upholstery.
5. Attach tool to end of hose.
6. Dry hands and plug cleaner into a properly
grounded outlet.
40
7. Set Wash/Rinse Selector to WASH. Turn
cleaner ON.
8. Gently press the tool onto the fabric. Press the
trigger and slowly pull the nozzle over the
fabric (Fig. 40).
9. Overlap strokes by 1/2 inch to help prevent
streaking.
10. Make additional strokes without pressing the
trigger to remove more solution.
To clean in corners or creases, lift the tool one
half inch from the fabric and press the solution
trigger.
11. For heavily soiled areas, it may be necessary
to repeat the cleaning process. Make
crisscrossing strokes to the original pattern;
overlap each pass (Fig. 41).
Make no more than 2 passes with the solution
over any one area to prevent over-wetting and
damage to fabric.
12. If you would like to rinse the carpet with water
only, set Wash/Rinse Setting switch to RINSE
(Fig. 42). For best cleaning results, Hoover
recommends to rinse the carpet with water
only. This will remove residual carpet cleaning
solution from your carpets. Then set Wash/
Rinse Selector to rinse and repeat steps 7 and 8.
If additional cleaning is necessary, wait until the
upholstery is completely dry before using the tool
again.
Empty Dirty Water Tank when the motor sound
becomes higher pitched and there is a loss in
suction (see “Automatic Shut-Off”).
When finished cleaning, follow “After Cleaning”
and “After Using Tool” instructions.
41
42