Husqvarna 525iLST Owner Manual - Page 17

To clean the product, the battery and, the battery charger, To lubricate the bevel gear, CAUTION

Get Husqvarna 525iLST PDF manuals and user guides View all Husqvarna 525iLST manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Maintenance Make sure that the blade is correctly centered, is sharp, and not damaged. An off-center blade will cause vibration that could result in damage to the product. Make sure that the locknut of the cutting equipment is tightened correctly. Make sure that the transport guard for the blade is not damaged and that the transport guard can be attached correctly. Examine all couplings and connections. Make sure they are not damaged and free from dirt. Make sure that the bevel gear is filled correctly with grease, refer to To lubricate the bevel gear on page 17. If not, use Husqvarna bevel gear grease. Lubricate the drive shaft end in the lower shaft coupling. Make sure that the air intake of the motor is not dirty. Clean the air intake with compressed air. Do a check of the connections between the battery and the product. Do a check of the connection between the battery and the battery charger. Daily X X X Weekly Monthly X X X X X To clean the product, the battery and the battery charger 1. Clean the product with a dry cloth after use. 2. Clean the battery and battery charger with a dry cloth. Keep the battery guide tracks clean. 3. Make sure that the terminals on the battery and the battery charger are clean before the battery is put in the battery charger or the product. To lubricate the bevel gear 1. Remove the cutting equipment. 2. Put the product with the grease plug at its highest position. 3. Remove the grease plug. 4. Look into the grease plug hole and turn the drive shaft. The grease level (A) must be in level with the top of the gear cogs (B). A B 5. If the grease level is too low fill the bevel gear with Husqvarna bevel gear grease. Fill slowly and turn the drive shaft as you apply the bevel gear grease, stop at the correct level (B). CAUTION: An incorrect quantity of grease can cause damage to the bevel gear. 6. Install the grease plug. 1920 - 001 - 28.11.2022 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
Maintenance
Daily
Weekly
Monthly
Make sure that the blade is correctly centered, is sharp, and not damaged. An
off-center blade will cause vibration that could result in damage to the product.
X
Make sure that the locknut of the cutting equipment is tightened correctly.
X
Make sure that the transport guard for the blade is not damaged and that the
transport guard can be attached correctly.
X
Examine all couplings and connections. Make sure they are not damaged and
free from dirt.
X
Make sure that the bevel gear is filled correctly with grease, refer to
To lubricate
the bevel gear on page 17
. If not, use Husqvarna bevel gear grease.
X
Lubricate the drive shaft end in the lower shaft coupling.
X
Make sure that the air intake of the motor is not dirty. Clean the air intake with
compressed air.
X
Do a check of the connections between the battery and the product. Do a check
of the connection between the battery and the battery charger.
X
To clean the product, the battery and
the battery charger
1.
Clean the product with a dry cloth after use.
2.
Clean the battery and battery charger with a dry
cloth. Keep the battery guide tracks clean.
3.
Make sure that the terminals on the battery and the
battery charger are clean before the battery is put in
the battery charger or the product.
To lubricate the bevel gear
1.
Remove the cutting equipment.
2.
Put the product with the grease plug at its highest
position.
3.
Remove the grease plug.
4.
Look into the grease plug hole and turn the drive
shaft. The grease level (A) must be in level with the
top of the gear cogs (B).
A
B
5.
If the grease level is too low fill the bevel gear with
Husqvarna bevel gear grease. Fill slowly and turn
the drive shaft as you apply the bevel gear grease,
stop at the correct level (B).
CAUTION:
An incorrect quantity of
grease can cause damage to the bevel
gear.
6.
Install the grease plug.
1920 - 001 - 28.11.2022
17