Home » Husqvarna Manuals » Lawn Mowers » Husqvarna V548 » Manual Viewer

Husqvarna V548 Owner Manual - Page 4

Stand on or walk behind position, Steering controls, Operator Presence Control (OPC), Ignition key - blades

Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

11. PTO button 12. Transport latch 13. Parking brake 14. Fuel shut-off valve 15. Deck lifting lever 16. Type plate 17. Adjustment levers for the adjustable bar 18. Adjustable bar Stand on or walk behind position The product can be operated as a stand on or walk behind lawn mower. The latch on the rear part of the product holds the stand on platform in a folded position. Refer to To set the product in stand on or walk behind position on page 11. • Run with accessory / headlights position (B) • Run position (C) • Start position (D) A B C D Throttle control The throttle control adjusts the speed of the engine and the speed of the blades if the blades are engaged. The throttle control has 2 end positions, idle speed and full throttle. A B Steering controls The direction of the product is controlled by the 2 control levers. Refer to Product overview on page 3. The control levers can be moved forward and rearward from a neutral position. Refer to To operate the product on page 13. Operator Presence Control (OPC) The OPC engages when the operator lifts the hands from the control levers. The engine and the drive to the blades stop if the blades are engaged or the parking brake is not applied. Refer to Operation conditions on page 8. Ignition key The ignition key is used to start and stop the engine. The ignition key has 4 positions: • Stop position (A) • Idle speed (A) - decreases the engine speed. • Full throttle (B) - increases the engine speed. CAUTION: Do not operate the engine at idle speed (A) for longer time than necessary. Too much operation time at idle speed can decrease the life of the spark plugs. Choke control The choke control is used for cold starts to supply more fuel to the engine. Pull up the choke control when you start a cold engine. Refer to Product overview on page 3 for the position of the choke control. PTO (Power Take-Off) button The PTO button engages and disengages the PTO clutch and the cutting deck or other equipment connected to it. The correct start conditions must be obeyed to engage the drive of the blades. Refer to Operation conditions on page 8 for the correct start conditions. 4 1994 - 002 - 05.12.2022

Section	Page
Contents	2
Conformity certificates	2
USA requirements	2
Introduction	2
Pre-delivery inspection and product numbers	2
Product description	3
Intended use	3
Support / Help	3
Product overview	3
Stand on or walk behind position	4
Steering controls	4
Operator Presence Control (OPC)	4
Ignition key	4
Throttle control	4
Choke control	4
PTO (Power Take-Off) button	4
Fuel gauge	5
Fuel shut-off valve	5
Fuses	5
Hour meter	5
Symbols on the product	5
Product liability	6
Safety	6
Safety definitions	6
General safety instructions	6
Safety instructions regarding children	7
Safety instructions for operation	7
Safety instructions for operation on slopes	7
Safety instructions for operation on slopes	8
Personal protective equipment	8
Safety devices on the product	8
To do a check of the ignition lock	8
Operation conditions	8
Parking brake	8
Muffler	9
To do a check of the muffler	9
Spark arrestor	9
Protective covers	9
Fuel safety	9
Transport safety	9
Hauling	9
Battery safety	9
Safety instructions for maintenance	10
Operation	10
Introduction	10
To operate the product for the first time	10
To do before you operate the product	11
To fill fuel	11
To set the product in stand on or walk behind position	11
To adjust the adjustable bar	11
To engage and disengage the parking brake	12
To disengage and engage the drive system	12
To set the cutting deck in transport position or mow position	12
To set the cutting height	12
To start the engine	12
To operate the product	13
To stop the engine	14
To adjust the tracking speed	14
To get a good cutting result	14
To do a 3-point turn	14
Maintenance	15
Introduction	15
Maintenance schedule	15
Maintenance schedule for the operator	15
To clean the product	17
To clean the engine and the muffler	17
To clean the battery	17
To remove the covers	17
To remove and install the engine cover	17
To do a check of the parking brake	18
To charge the battery	18
To do an emergency start of the engine	18
To connect the jumper cables	18
To remove the jumper cables	18
To remove and install the battery	18
Tire pressure	19
To remove and install the front wheels	19
To adjust the anti-scalp rollers	19
To adjust the parallelism of the cutting deck	19
To adjust the neutral position	20
To adjust the neutral switches	20
To examine the blades	21
To replace the blades	21
To remove the deck drive belt	21
To install the deck drive belt	21
To remove the deck belt	21
To install the deck belt	22
To remove the pump belt	22
To install the pump belt	22
To do a check of the engine oil level	22
To replace the engine oil	23
To do a check of the hydraulic oil level	23
Lubrication, general information	24
Lubrication schedule	24
To lubricate the front wheels	25
To lubricate the cutting deck spindles	25
Troubleshooting	25
Troubleshooting schedule	25
Transportation, storage and disposal	27
Transportation	27
Storage	27
Disposal	28
Technical data	29
Technical data	29
Battery charging times	30
Service	31
Service	31
Contenido	32
Certificados de conformidad	32
Requisitos para EE. UU.	32
Introducción	32
Inspección previa a la entrega y números de producto	32
Descripción del producto	33
Uso previsto	33
Soporte/ayuda	33
Descripción general del producto	34
Posición de caminar o permanecer de pie en la parte trasera	34
Controles de la dirección	35
Control de presencia del operador (OPC)	35
Llave de encendido	35
Control del acelerador	35
Estrangulador	35
Botón de toma de fuerza (PTO)	35
Indicador de combustible	36
Válvula de corte de combustible	36
Fusibles	36
Medidor de horas	36
Símbolos en el producto	36
Responsabilidad del fabricante	37
Seguridad	37
Definiciones de seguridad	37
Instrucciones generales de seguridad	37
Instrucciones de seguridad relacionadas con los niños	38
Instrucciones de seguridad para el funcionamiento	38
Instrucciones de seguridad para el uso en pendientes	38
Instrucciones de seguridad para el uso en pendientes	39
Equipo de protección personal	39
Dispositivos de seguridad en el producto	39
Para comprobar el bloqueo del encendido	40
Condiciones de funcionamiento	40
Freno de estacionamiento	40
Silenciador	40
Para revisar el silenciador	40
Apagachispas	40
Cubiertas protectoras	40
Seguridad de combustible	40
Seguridad del transporte	41
Transporte	41
Seguridad de la batería	41
Instrucciones de seguridad para el mantenimiento	41
Funcionamiento	42
Introducción	42
Para usar el producto por primera vez	42
Haga lo siguiente antes de usar el producto	42
Para agregar combustible	42
Para colocar el producto en posición de caminar o permanecer de pie en la parte trasera	43
Para ajustar la barra ajustable	43
Para acoplar y desacoplar el freno de estacionamiento	43
Para desacoplar y acoplar el sistema de transmisión	43
Para colocar el equipo de corte en la posición de transporte o posición de corte	44
Ajuste de la altura de corte	44
Para arrancar el motor	44
Para hacer funcionar el producto	45
Para detener el motor	46
Para ajustar la velocidad de desplazamiento	46
Para conseguir un buen resultado de corte	46
Para hacer un giro de 3 puntos	47
Mantenimiento	47
Introducción	47
Programa de mantenimiento	47
Programa de mantenimiento para el usuario	47
Para limpiar el producto	49
Para limpiar el motor y el silenciador	50
Para limpiar la batería	50
Para quitar las cubiertas	50
Para retirar e instalar la cubierta del motor	50
Para comprobar el freno de estacionamiento	50
Para cargar la batería	50
Para hacer una parada de emergencia del motor	50
Para conectar los cables de puente	50
Para retirar los cables de puente	51
Para retirar e instalar la batería	51
Presión de los neumáticos	51
Para retirar e instalar las ruedas delanteras	51
Para ajustar las ruedas de apoyo	51
Para ajustar el paralelismo del equipo de corte	52
Para ajustar la posición neutra	52
Para ajustar los interruptores de neutro	53
Para examinar las cuchillas	54
Para sustituir las hojas	54
Para retirar la correa de transmisión del equipo	54
Para instalar la correa de transmisión del equipo	54
Para extraer la correa del equipo	54
Para instalar la correa del equipo	55
Para extraer la correa de la bomba	55
Para instalar la correa de la bomba	55
Para revisar el nivel de aceite del motor	55
Para cambiar el aceite del motor:	56
Para revisar el nivel de aceite hidráulico	56
Lubricación; información general	57
Programa de lubricación	57
Para lubricar las ruedas delanteras	58
Para lubricar los ejes del equipo de corte	58
Solución de problemas	58
Programa de solución de problemas	58
Transporte, almacenamiento y eliminación de residuos	61
Transporte	61
Almacenamiento	61
Eliminación	61
Datos técnicos	62
Datos técnicos	62
Tiempos de carga de la batería	63
Servicio	64

Match case Limit results 1 per page

11. PTO button

12. Transport latch

13. Parking brake

14. Fuel shut-off valve

15. Deck lifting lever

16. Type plate

17. Adjustment levers for the adjustable bar

18. Adjustable bar

Stand on or walk behind position

The product can be operated as a stand on or walk

behind lawn mower. The latch on the rear part of

the product holds the stand on platform in a folded

position. Refer to

To set the product in stand on or

walk behind position on page 11

Steering controls

The direction of the product is controlled by the 2

control levers. Refer to

Product overview on page

. The control levers can be moved forward and

rearward from a neutral position. Refer to

To operate

the product on page 13

Operator Presence Control (OPC)

The OPC engages when the operator lifts the hands

from the control levers. The engine and the drive

to the blades stop if the blades are engaged or

the parking brake is not applied. Refer to

Operation

conditions on page 8

Ignition key

The ignition key is used to start and stop the engine.

The ignition key has 4 positions:

•

Stop position (A)

•

Run with accessory / headlights position (B)

•

Run position (C)

•

Start position (D)

Throttle control

The throttle control adjusts the speed of the engine

and the speed of the blades if the blades are

engaged. The throttle control has 2 end positions,

idle speed and full throttle.

•

Idle speed (A) - decreases the engine speed.

•

Full throttle (B) - increases the engine speed.

CAUTION:

Do not operate the

engine at idle speed (A) for longer time

than necessary. Too much operation

time at idle speed can decrease the life

of the spark plugs.

Choke control

The choke control is used for cold starts to supply

more fuel to the engine. Pull up the choke control

when you start a cold engine.

Refer to

Product overview on page 3

for the position

of the choke control.

PTO (Power Take-Off) button

The PTO button engages and disengages the PTO

clutch and the cutting deck or other equipment

connected to it. The correct start conditions must

be obeyed to engage the drive of the blades. Refer

Operation conditions on page 8

for the correct

start conditions.

1994 - 002 - 05.12.2022