IBM 6400-I15 Operation Guide - Page 103

hammer bank power cable shorted

Get IBM 6400-I15 PDF manuals and user guides View all IBM 6400-I15 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 103 highlights

088 CONTROLLER 23.5V 089 RIBBON STALL CHECK RIBBON 090 SHUTTLE COVER OPEN CLOSE SHUTTLE COVER 092 RIBBON DRIVER CIRCUIT 101 UPPER DRIVER SHORT 102 LOWER DRIVER SHORT 107 HAMMER COIL HOT 110 STACK OVERFLOW SEE USER'S GUIDE status and fault messages Controller voltage failure. Contact an IBM service representative. No ribbon movement. Make sure the ribbon is not twisted and the forms thickness lever is set to match thickness of media being used. If fault reoccurs, contact an IBM service representative. Shuttle cover is missing, damaged, or not correctly installed. Contact an IBM service representative. Controller board does not detect ribbon drive motor. Contact an IBM service representative. Hammer driver circuits on the controller board shorted to ground. Contact an IBM service representative. Circuit(s) on the hammer bank or in the hammer bank power cable shorted to ground. Contact an IBM service representative. One or more hammer coils are overheating. Stop printing and allow the printer to cool for five minutes. If the fault reoccurs, contact an IBM service representative. Fatal firmware error on the controller board. Contact an IBM service representative. Operator's Guide 89

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
status and fault messages
89
Operator’
s Guide
Controller voltage failure. Contact an IBM
service representative.
No ribbon movement. Make sure the
ribbon is not twisted and the forms
thickness lever is set to match thickness
of media being used. If fault reoccurs,
contact an IBM service representative.
Shuttle cover is missing, damaged, or not
correctly installed. Contact an IBM
service representative.
Controller board does not detect ribbon
drive motor. Contact an IBM service
representative.
Hammer driver circuits on the controller
board shorted to ground. Contact an IBM
service representative.
Circuit(s) on the hammer bank or in the
hammer bank power cable shorted to
ground. Contact an IBM service
representative.
One or more hammer coils are
overheating. Stop printing and allow the
printer to cool for five minutes. If the fault
reoccurs, contact an IBM service
representative.
Fatal firmware error on the controller
board. Contact an IBM service
representative.
088
CONTROLLER 23.5V
089 RIBBON ST
ALL
CHECK RIBBON
090 SHUTTLE COVER OPEN
CLOSE SHUTTLE COVER
092 RIBBON DRIVER CIRCUIT
101 UPPER DRIVER SHORT
102 LOWER DRIVER SHORT
107 HAMMER COIL HOT
1
10 ST
ACK OVERFLOW
SEE USER’S GUIDE