Home » IBM Manuals » Desktops » IBM 8307 » Manual Viewer

IBM 8307 Hardware Maintenance Manual - Page 53

Installing, memory

UPC - 087944816577

Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

The following illustration shows the locations of parts on the system board. 1 Microprocessor 2 DIMM connector 1 3 DIMM connector 2 4 Power connector 5 Diskette drive connector 6 Primary IDE connector 7 Front panel connector 8 Secondary IDE connector 9 Battery 10 Clear CMOS/Recovery jumper 11 SCSI LED connector 12 PCI slots 13 Front panel audio connector 14 CD-ROM audio connector 15 AGP slot (some models) 16 Serial connector Installing memory Your computer has two connectors for installing dual inline memory modules (DIMMs) that provide up to a maximum of 2.0 GB of system memory. When installing DIMMs, the following rules apply: v Fill each system memory connector sequentially, starting at DIMM connector 1. v Use 2.5 V, 184-pin, 266 MHz double data rate synchronous dynamic random access memory (DDR SDRAM). v Use 128 MB, 256 MB, 512 MB or 1.0 GB (when available) DIMMs in any combination. v DIMMs are 38.1 mm (1.5 inches) in height. Note: Only DDR SDRAM DIMMs can be used. To install a DIMM: 1. Remove the cover. See "Removing the cover" on page 40. 2. To locate the DIMM connectors. See "Identifying parts on the system board" on page 44. Chapter 5. Installing Options 47

Section	Page
Contents	5
Chapter 1. About this manual	7
Important Safety Information	7
Chapter 2. General Checkout	9
Chapter 3. General information	11
Features	11
Types 8301 and 8302	11
Types 8303, 8304, and 8312	13
Types 8305, 8306, 8309, and 8313	15
Types 8307, 8308, 8310, 8311, 8314, and 8315	17
Physical specifications	19
Types 8301 and 8302	19
Types 8303, 8304 and 8312	20
Types 8305, 8306, 8309, and 8313	22
Types 8307, 8308, 8310, 8311, 8314, and 8315	23
Available options	24
Types 8301 and 8302	24
Types 8303, 8304 and 8312	25
Types 8305, 8306, 8309, and 8313	26
Types 8307, 8308, 8310, 8311, 8314, and 8315	27
Chapter 4. Diagnostics	29
Setup Utility program	30
Product Recovery Program menu	31
Diagnostics	32
Diagnostics program download	32
Navigating through the diagnostics programs	32
Running diagnostics tests	32
Test selection	32
Test results	33
Fixed disk advanced test (FDAT)	33
Quick and Full erase - hard drive	35
Viewing the test log	36
Chapter 5. Installing Options	37
Installing external options	37
Locating connectors on the front	37
Types 8301 and 8302	37
Types 8303, 8304, and 8312	37
Types 8305, 8306, 8309, and 8313	38
Types 8307, 8308, 8310, 8311, 8314, and 8315	38
Locating the connectors on the rear	39
Types 8301 and 8302	39
Types 8303, 8304, and 8312	41
Types 8305, 8306, 8309, and 8313	43
Types 8307, 8308, 8310, 8311, 8314, and 8315	43
Obtaining device drivers	45
Installing internal options	45
Removing the cover	46
Types 8303, 8304, and 8312	46
Types 8305, 8306, 8309, and 8313	46
Types 8307, 8308, 8310, 8311, 8314, and 8315	47
Locating components	48
Types 8303, 8304, and 8312	48
Types 8305, 8306, 8309, and 8313	49
Types 8307, 8308, 8310, 8311, 8314, and 8315	50
Identifying parts on the system board	50
Types 8303, 8304, and 8312	50
Types 8305, 8306, 8309, and 8313	51
Types 8307, 8308, 8310, 8311, 8314, and 8315	52
Installing memory	53
Installing adapters	54
Types 8303, 8304, and 8312	54
Installing adapters in Types 8305, 8306, 8309, and 8313	56
Installing adapters in Types 8307, 8308, 8310, 8311, 8314, and 8315	57
Installing internal drives	58
Types 8301 and 8302	58
Types 8303, 8304, and 8312	59
Installing internal drives in Types 8305, 8306, 8309, and 8313	62
Installing internal drives in Types 8307, 8308, 8310, 8311, 8314, and 8315	65
Installing a rope clip	70
Types 8303, 8304, and 8312	70
Installing a rope clip in Types 8305, 8306, 8309, and 8313	70
Installing a rope clip in Types 8307, 8308, 8310, 8311, 8314, and 8315	71
Changing the battery	73
Replacing the cover and connecting the cables	73
Types 8303, 8304, and 8312	73
Types 8305, 8306, 8309, and 8313	74
Types 8307, 8308, 8310, 8311, 8314, and 8315	74
Chapter 6. FRU Removals	77
Removing the cover Types 8301 and 8302	77
Removing the CD-ROM drive Types 8301 and 8302	77
Front bezel Types 8307, 8308, 8310, 8311, 8314, and 8315	78
Replacing a microprocessor	78
Hard disk drive removal	79
Types 8303, 8304, and 8312	79
Drive specifications	79
Installing a drive	79
Types 8305, 8306, 8309, and 8313	80
To connect an additional IDE hard disk drive	82
Types 8307, 8308, 8310, 8311, 8314, and 8315	83
Power supply removal	83
Types 8301 and 8302	83
Types 8303, 8304, and 8312	84
Types 8305, 8306, 8309, and 8313	85
Types 8307, 8308, 8310, 8311, 8314, and 8315	86
System board removal	86
Types 8301 and 8302	86
Types 8303, 8304, and 8312	87
Types 8305, 8306, 8309, and 8313	88
Types 8307, 8308, 8310, 8311, 8314, and 8315	89
Replacing the cover, Types 8301 and 8302	89
Chapter 7. Symptom-to-FRU Index	93
Hard disk drive boot error	93
Power Supply Errors	93
Diagnostic error codes	95
Beep symptoms	113
No-beep symptoms	115
POST error codes	116
Miscellaneous error messages	131
Undetermined problems	133
Chapter 8. Parts listing	135
Chapter 9. Additional Service Information	269
Security features	269
Passwords	269
Power-on password	269
Removing a power-on password	269
Administrator password	269
Administrator password control	270
Operating system password	270
Vital product data	270
Management Information Format (MIF)	270
Alert on LAN	271
BIOS levels	271
Flash update procedures	271
Flash from Operating System (WinPhlash)	272
Flash from CD-ROM ISO image	272
Flash recovery boot block jumper	273
Power management	275
Automatic configuration and power interface (ACPI) BIOS	275
Advanced Power Management	275
Automatic Hardware Power Management features	275
Setting Automatic Hardware Power Management features	275
Automatic Power-On features	276
Chapter 10. Related service information	277
Safety information	277
General safety	277
Electrical safety	278
Safety inspection guide	279
Handling electrostatic discharge-sensitive devices	280
Grounding requirements	281
Safety notices (multi-lingual translations)	281
Send us your comments!	310
Problem determination tips	311
Notices	311

Match case Limit results 1 per page

The

following

illustration

shows

the

locations

parts

the

system

board.

±1²

Microprocessor

±9²

Battery

±2²

DIMM

connector

±10²

Clear

CMOS/Recovery

jumper

±3²

DIMM

connector

±11²

SCSI

LED

connector

±4²

Power

connector

±12²

PCI

slots

±5²

Diskette

drive

connector

±13²

Front

panel

audio

connector

±6²

Primary

IDE

connector

±14²

CD-ROM

audio

connector

±7²

Front

panel

connector

±15²

AGP

slot

(some

models)

±8²

Secondary

IDE

connector

±16²

Serial

connector

Installing

memory

Your

computer

has

two

connectors

for

installing

dual

inline

memory

modules

(DIMMs)

that

provide

maximum

2.0

system

memory.

When

installing

DIMMs,

the

following

rules

apply:

Fill

each

system

memory

connector

sequentially,

starting

DIMM

connector

Use

2.5

184-pin,

266

MHz

double

data

rate

synchronous

dynamic

random

access

memory

(DDR

SDRAM).

Use

128

MB,

256

MB,

512

1.0

(when

available)

DIMMs

any

combination.

DIMMs

are

38.1

(1.5

inches)

height.

Note:

Only

DDR

SDRAM

DIMMs

can

used.

install

DIMM:

Remove

the

cover.

See

“Removing

the

cover”

page

40.

locate

the

DIMM

connectors.

See

“Identifying

parts

the

system

board”

page

44.

Chapter

Installing

Options