IBM 86481BU User Guide - Page 33

Using, Adaptec, Configuration, Utility, programs, Serial

Get IBM 86481BU PDF manuals and user guides View all IBM 86481BU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Using the Adaptec RAID Configuration Utility programs (for Serial ATA RAID) | Use the Array Configuration Utility, in the Adaptec RAID Configuration Utility | programs, to add RAID level-0 and level-1 functionality to the integrated Serial ATA | (SATA) controller. This utility is part of the BIOS code in the server. For additional | information about using the Adaptec RAID Configuration Utility programs, see the | documentation on the IBM ServeRAID-7e (Adaptec HostRAID) Support CD. If this | CD did not come with your server, you can download it from the IBM Web site at | http://www.ibm.com/pc/support/. The integrated Serial ATA RAID feature (SATA HostRAID) comes disabled by default. You must enable it and install the device drivers before you can use it. The SATA RAID feature configuration utilities, device drivers, and information are available on the IBM ServeRAID-7e (Adaptec HostRAID) Support CD. Enabling the Serial ATA HostRAID feature Complete the following steps to enable the SATA RAID feature: | 1. Turn on the server. 2. When the prompt Press F1 for Configuration/Setup appears, press F1. If you have set an administrator password, you are prompted to type the password. 3. Select Advanced Setup. 4. Make sure the setting for Serial ATA is Enabled. 5. Scroll down and select SATA RAID Enable. 6. Select Enabled. 7. Press Esc; then, select Yes to save the changes. Using the Serial ATA HostRAID feature The instructions in this section are for using the Array Configuration Utility program to access and perform an initial RAID level-1 configuration on the integrated SATA controller. If you install a RAID adapter in the server, use the configuration method described in the instructions that come with that adapter to view or change settings for the attached devices. Note: The integrated SATA controller supports only two hard disk drives. For the server (SATA models) to support up to four SATA hard disk drives, an optional SATA RAID adapter must be installed in the server. See the Option Installation Guide for more information. See the documentation on the IBM ServeRAID-7e (Adaptec HostRAID) Support CD for additional information about using the Array Configuration Utility program to create, configure, and manage arrays. Configuring the controller: Complete the following steps to use the Array Configuration Utility program to configure a RAID level-1 array on your server. 1. Turn on the server and watch the monitor screen. 2. When the message Press for Adaptec RAID Configuration Utility appears, press Ctrl+A. 3. Select Array Configuration Utility (ACU). 4. Select Create Array. 5. From the list of ready drives, select the two drives that you want to group into the array. 6. When asked to select the RAID level, select RAID-1. Chapter 2. Configuring the server 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
Using
the
Adaptec
RAID
Configuration
Utility
programs
(for
Serial
ATA
RAID)
Use
the
Array
Configuration
Utility,
in
the
Adaptec
RAID
Configuration
Utility
programs,
to
add
RAID
level-0
and
level-1
functionality
to
the
integrated
Serial
ATA
(SATA)
controller.
This
utility
is
part
of
the
BIOS
code
in
the
server.
For
additional
information
about
using
the
Adaptec
RAID
Configuration
Utility
programs,
see
the
documentation
on
the
IBM
ServeRAID-7e
(Adaptec
HostRAID)
Support
CD.
If
this
CD
did
not
come
with
your
server,
you
can
download
it
from
the
IBM
Web
site
at
The
integrated
Serial
ATA
RAID
feature
(SATA
HostRAID)
comes
disabled
by
default.
You
must
enable
it
and
install
the
device
drivers
before
you
can
use
it.
The
SATA
RAID
feature
configuration
utilities,
device
drivers,
and
information
are
available
on
the
IBM
ServeRAID-7e
(Adaptec
HostRAID)
Support
CD.
Enabling
the
Serial
ATA
HostRAID
feature
Complete
the
following
steps
to
enable
the
SATA
RAID
feature:
1.
Turn
on
the
server.
2.
When
the
prompt
Press
F1
for
Configuration/Setup
appears,
press
F1.
If
you
have
set
an
administrator
password,
you
are
prompted
to
type
the
password.
3.
Select
Advanced
Setup
.
4.
Make
sure
the
setting
for
Serial
ATA
is
Enabled
.
5.
Scroll
down
and
select
SATA
RAID
Enable
.
6.
Select
Enabled
.
7.
Press
Esc;
then,
select
Yes
to
save
the
changes.
Using
the
Serial
ATA
HostRAID
feature
The
instructions
in
this
section
are
for
using
the
Array
Configuration
Utility
program
to
access
and
perform
an
initial
RAID
level-1
configuration
on
the
integrated
SATA
controller.
If
you
install
a
RAID
adapter
in
the
server,
use
the
configuration
method
described
in
the
instructions
that
come
with
that
adapter
to
view
or
change
settings
for
the
attached
devices.
Note:
The
integrated
SATA
controller
supports
only
two
hard
disk
drives.
For
the
server
(SATA
models)
to
support
up
to
four
SATA
hard
disk
drives,
an
optional
SATA
RAID
adapter
must
be
installed
in
the
server.
See
the
Option
Installation
Guide
for
more
information.
See
the
documentation
on
the
IBM
ServeRAID-7e
(Adaptec
HostRAID)
Support
CD
for
additional
information
about
using
the
Array
Configuration
Utility
program
to
create,
configure,
and
manage
arrays.
Configuring
the
controller:
Complete
the
following
steps
to
use
the
Array
Configuration
Utility
program
to
configure
a
RAID
level-1
array
on
your
server.
1.
Turn
on
the
server
and
watch
the
monitor
screen.
2.
When
the
message
Press
<CTRL><A>
for
Adaptec
RAID
Configuration
Utility
appears,
press
Ctrl+A.
3.
Select
Array
Configuration
Utility
(ACU)
.
4.
Select
Create
Array
.
5.
From
the
list
of
ready
drives,
select
the
two
drives
that
you
want
to
group
into
the
array.
6.
When
asked
to
select
the
RAID
level,
select
RAID-1
.
Chapter
2.
Configuring
the
server
21
|
|
|
|
|
|
|
|