IBM 8874 Installation Guide - Page 30

fully-open

Get IBM 8874 - eServer xSeries MXE 460 PDF manuals and user guides
UPC - 000435813008
View all IBM 8874 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

9. Remove the protective cover, tape, or label from the surface of the microprocessor socket, if any is present. 10. Lift the microprocessor-release lever to the fully-open position (approximately 135° angle). Lever closed Lever fully open 11. Touch the static-protective package that contains the new microprocessor to any unpainted metal surface on the server; then, remove the microprocessor from the package. Attention: To avoid bending the pins on the microprocessor, do not use excessive force when pressing it into the socket. 12. Position the microprocessor over the microprocessor socket as shown in the following illustration. Carefully press the microprocessor into the socket. Microprocessor Microprocessor orientation indicator Microprocessor connector Microprocessorrelease lever 13. Close the microprocessor-release lever to secure the microprocessor. 14. Remove the heat sink from its package and remove the cover from the bottom of the heat sink. 15. Position the heat sink above the microprocessor; then, press the heat sink into place and close the heat-sink release lever. Note: If you are installing an additional microprocessor in microprocessor socket 3 or 4, a VRM must also be installed. 16. If necessary, install a VRM in the correct connector. 17. Reinstall the microprocessor tray in the server: a. Install the air baffle in the microprocessor tray. b. Place the air baffle on top of the heat sinks and the microprocessor baffles. c. Make sure that the microprocessor-tray release latch is open; then, push the microprocessor tray into the server. d. Close the tray levers and make sure they are securely latched. 18 IBM xSeries 460 Type 8872 and xSeries MXE 460 Type 8874: Installation Guide ERserver

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
9.
Remove
the
protective
cover,
tape,
or
label
from
the
surface
of
the
microprocessor
socket,
if
any
is
present.
10.
Lift
the
microprocessor-release
lever
to
the
fully-open
position
(approximately
135°
angle).
Lever closed
Lever fully
open
11.
Touch
the
static-protective
package
that
contains
the
new
microprocessor
to
any
unpainted
metal
surface
on
the
server;
then,
remove
the
microprocessor
from
the
package.
Attention:
To
avoid
bending
the
pins
on
the
microprocessor,
do
not
use
excessive
force
when
pressing
it
into
the
socket.
12.
Position
the
microprocessor
over
the
microprocessor
socket
as
shown
in
the
following
illustration.
Carefully
press
the
microprocessor
into
the
socket.
Microprocessor
orientation indicator
Microprocessor-
release lever
Microprocessor
connector
Microprocessor
13.
Close
the
microprocessor-release
lever
to
secure
the
microprocessor.
14.
Remove
the
heat
sink
from
its
package
and
remove
the
cover
from
the
bottom
of
the
heat
sink.
15.
Position
the
heat
sink
above
the
microprocessor;
then,
press
the
heat
sink
into
place
and
close
the
heat-sink
release
lever.
Note:
If
you
are
installing
an
additional
microprocessor
in
microprocessor
socket
3
or
4,
a
VRM
must
also
be
installed.
16.
If
necessary,
install
a
VRM
in
the
correct
connector.
17.
Reinstall
the
microprocessor
tray
in
the
server:
a.
Install
the
air
baffle
in
the
microprocessor
tray.
b.
Place
the
air
baffle
on
top
of
the
heat
sinks
and
the
microprocessor
baffles.
c.
Make
sure
that
the
microprocessor-tray
release
latch
is
open;
then,
push
the
microprocessor
tray
into
the
server.
d.
Close
the
tray
levers
and
make
sure
they
are
securely
latched.
18
IBM
ERserver
xSeries
460
Type
8872
and
xSeries
MXE
460
Type
8874:
Installation
Guide