Icom HM-195GB Instructions - Page 6
Channel Auto Switch function
View all Icom HM-195GB manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 6 highlights
¤6 DSC Settings DDAutomatic Acknowledgement qqEnter either "INDIVIDUAL ACK," "POSITION ACK" or "TEST ACK" in the DSC Settings menu. wwRotate Dial to select "Auto TX" or "Manual TX," then push [ENT]. • Push [BACK] to cancel and return to the DSC Settings menu. eePush [EXIT] to return to the normal operating mode. DDChannel Auto Switch function (For only USA version.) qqE nter "CH AUTO SWITCH" in the DSC Settings menu. wwRotate Dial to set the Channel Auto Switch function to "Auto (No Delay)," "10 Second Delay" or "OFF," then push [ENT]. • Push [BACK] to cancel and return to the DSC Settings menu. eePush [EXIT] to return to the normal operating mode. DDChannel 16 Switch function qqE nter "CH 16 SWITCH" in the DSC Settings menu. wwRotate Dial to set the Channel 16 Switch function to "Auto (No Delay)," "10 Second Delay" or "OFF," then push [ENT]. • Push [BACK] to cancel and return to the DSC Settings menu. eePush [EXIT] to return to the normal operating mode. DDDSC Data Output qqEnter "DSC DATA OUTPUT" in the DSC Settings menu. eeRotate Dial to set the DSC Data Output function to "All Sta- tion," "List Station" or "OFF," then push [ENT]. • Push [BACK] to cancel and return to the DSC Settings menu. eePush [EXIT] to return to the normal operating mode. DDAlarm qqE nter "ALARM" in the DSC Settings menu. wwRotate Dial to select the status, then push [ENT]. • Push [BACK] to cancel and return to the DSC Settings menu. • "Safety," "Routine," "Warning," "Self-Terminate" and "Discrete" are selectable. (default: ON ) eeRotate Dial to set the Alarm setting to "ON" or "OFF." rrPush [EXIT] to return to the normal operating mode. DDChannel 70 Squelch level qqE nter "CH 70 SQL LEVEL" in the DSC Settings menu. wwRotate Dial to adjust the squelch level until the noise just disappears, then push [ENT]. • Push [BACK] to cancel and return to the DSC Settings menu. eePush [EXIT] to return to the normal operating mode. DDDSC Loop Test qqE nter "DSC LOOP TEST" in the DSC Settings menu. wwPush [ENT] to start the DSC loop test. • Push [BACK] to cancel and return to the DSC Settings menu. • When the transmit DSC and receive DSC signals are matched, "OK" appears. eePush [EXIT] to return to the normal operating mode. If "NG" appears in step w, either or both TX and RX DSC circuits has a problem. In that case, you will have to send the transceiver to your nearest dealer for repair. ¤7 Intercom operation This function is not available with the IC-M400BB. qqPush [INCM] to enter the Intercom mode. wwHold down [INCM CALL] to sound the intercom beeps. • T he transceiver and the command microphone sound beeps while holding down [INCM CALL]. • "CALL" appears. eeAfter releasing [INCM CALL], hold down [PTT] and speak into the microphone at a normal voice level. • "TALK" appears on the caller's display, or "LSTN" appears on the listener's display. • To adjust the HM-195's intercom volume level, rotate [VOL/ SQL](Dial) on the HM-195. rrAfter releasing [PTT] you can hear the response through the speaker. On the caller's display On the listener's display ttTo return to the normal operating mode, push [EXIT]. ¤8 RX Speaker function qqPush [RX ] to enter the RX Speaker mode. • T he RX Speaker volume level adjustment screen is displayed. wwRotate Dial or push [Y]/[Z to adjust the RX Speaker volume level, and then push [ENT]. • "RX " appears. eeTo return to normal operating mode, push [RX ]. • "RX " disappears. ¤9 PA (Public Address) function qqPush [PA] to enter the Public Address mode. wwHold down [PTT] and speak at a normal voice level. • While holding down [PTT], the screen below is displayed. • To adjust the PA volume level, rotate Dial. eePush [EXIT] to return to normal operating screen. ‹0 Horn function qqPush [HORN] to enter the Horn mode. wwHold down [HORN] to sound a horn. • While holding down [HORN], the horn sounds, and the screen below is displayed. • To adjust the horn volume level, rotate Dial. eePush [EXIT] to return to the normal operating screen. ‹1 Menu screen operation The Menu screen is used to change the transceiver's functions and the microphone's own functions, send DSC calls or show the entered MMSI and ATIS*1 codes and GPS information*2. *1 Appears only when the transceiver is the Dutch or German ver- sion. *2 Appears only when a GPS receiver compatible with NMEA0183 ver. 2.0 or 3.01 is connected to the transceiver. These instructions are for only the microphone's own functions. Refer to the transceiver's manual for the settings of the other functions. (Some functions cannot be selected from the HM-195.) DD Entering the Menu screen and operation qqPush [MENU]. wwRotate Dial or push to select the root item, and then push [ENT]. eeRotate Dial or push to select the item, and then push [ENT]. rrRotate Dial or push to select the option, and then push [ENT] to set it. ttP ush [EXIT] to exit the Menu screen. • Push [CLEAR] or [BACK] to return to the previous screen. • Backlight The function display and keys of the HM-195 can be backlit for better visibility under low light conditions. The backlight can be set to 7 levels and OFF. (Default: 7) • Display contrast The contrast of the HM-195's function display can be adjusted in 8 steps. Level 1 is the lowest contrast, and level 8 is the highest con- trast. (Default: 5) • Key Beep You can turn OFF beep tones for silent operation, or you can turn ON the tones to have confirmation beeps sound when a key is pushed. (Default: ON) • COMMANDMIC Speaker The HM-195's external speaker can be used instead of the in- ternal speaker. (Default: Internal Speaker) Regardless of this setting, the transceiver's microphone speaker is ON. ■■TIP If the transceiver supports, you can use the AIS functions and the Highway function with the HM-195. Push to display the Plotter screen or the Highway screen on the command mi- crophone screen. DDPlotter screen 1 2 3 4 5 q TARGET BOX 2 YOUR VESSEL ICON The vessel icon automatically points in the direction your vessel is heading, in 45 degree steps. When your vessel moves less than 2 knots per hour speed, is displayed. 3 TARGET ICONS AIS target: Vessel AIS target: Vessel (Friend) AIS target: A IS-SART, AIS-MOB, and EPIRB-AIS * AIS target: S earch and Rescue (SAR) aircraft AIS target: A ids to Navigation (AtoN) AIS target: A ids to Navigation (AtoN) virtual * AIS target: Base station * Waypoint: During navigation. * MOB *Blinks when the AIS target is closer than your CPA and TCPA settings (Danger target). 4 DISPLAY RANGE 5 DISPLAY FILTER INDICATOR Displayed when the type of targets on the Plotter screen is filtered. DDHighway screen 1 1 2 3 4 1 XTE LIMIT LINE 2 YOUR VESSEL ICON When your vessel moves less than 2 knots per hour speed, is displayed. 3 RANGE Displays the range (RNG) from your vessel to the target. 4 XTE Displays the Cross Track Error. +See "Instructions q" (z to ⁄5) or "Instructions w" (⁄6 to ¤2) for other functions. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan Apr. 2021 A7022D-3EX-4 Printed in Japan © 2012-2021 Icom Inc.