Icom HM-195GB Instructions - Page 7

INSTRUCTIONS r FOR IC-M400BB/ IC-M400BBE REMOTE-CONTROL MICROPHONE HM-195B HM-195SW ‹2 Menu Screen Operation 2 See "Instructions e" (‹1 Menu screen operation) for entering the menu screen operation. The Menu screen is used for setting infrequently changed values, function settings or sending DSC calls. DDMMSI/GPS Information The transceiver shows the entered MMSI code and GPS information. If the code is not entered, "NO DSC MMSI" is displayed. Menu lists ‹3 Radio Settings items DDScan type The transceiver has two scan types, Normal scan and Pri- ority scan. A Normal scan searches all Favorite channels in the selected channel group. A Priority scan sequentially searches all Favorite channels, while monitoring Channel 16.  (Default: Priority Scan*) DDChannel Group Except for the European version, a channel group suitable for your operating area can be selected. Depending on the transceiver version, INT, USA, CAN, ATIS or DSC may be selectable. • The screen below shows the USA version. *"Normal Scan" is the default for the USA version. DDScan timer The scan timer can be selected as a pause (OFF) or timer scan (ON). When OFF is selected, the scan pauses until the signal disappears.   (Default: OFF) • Priority scan: When ON is selected, the scan pauses for 5 seconds and then resumes, even if a signal has been received on any channel other than Channel 16. • Normal scan: When ON is selected, the scan pauses for 5 seconds and then resumes, even if a signal has been received on any channel. DDWeather alert (For only USA and Australian version.) A NOAA broadcast station transmits a weather alert tone before important weather information. (Default: OFF) • "WX " blinks until the transceiver is operated after the trans- ceiver detects the alert. • "WX " appears instead of "WX" when the function is set ON. ON with Scan: The preset weather channels are sequen- tially checked while scanning. ON: The previously selected (last used) weather channel is checked while scanning. OFF: The transceiver does not detect a weather alert tone. DDDual/Tri-watch This item can be selected as Dualwatch or Tri-watch. (p. 19) (Default: Dualwatch) DDCH Display You can select the number of digits to display the channel number. (Default: 4 Digits) • This setting may not be usable, depending on the transceiver's version or presetting. 3 Digits: The channel number is displayed in 3 digits, such as "01A." 4 Digits: The channel number is displayed in 4 digits, such as "1001." ‹4 Configurations See "Instructions e" (‹1 Menu screen operation) for Backlight, Display Contrast, Key Beep, and COMMANDMIC Speaker functions details. DDKey Assignment Desired functions can be assigned to Dial and the softkeys. qqWhen the "KEY ASSIGNMENT" screen is displayed, rotate Dial or push to select "Dial" or "Softkeys," and then push [ENT]. wwRotate Dial or push to select the desired position, and then push [ENT]. • To return to the default, select "Set default" and push [ENT]. For "Dial" assignment For "Softkeys" assignment eeRotate Dial or push to select the option, and then push [ENT] to set it is displayed next to the selected option. DDUTC Offset Set the offset time between the UTC (Universal Time Coor- dinated) and your local time to between -14:00 and +14:00 (in 1 minute steps).  (Default: 00:00) DDNoise Cancel Set the Noise Cancel function for both receive and transmit. qqW hen the "NOISE CANCEL" screen is displayed, rotate Dial or push to select "RX" or "TX," and then push [ENT]. For "Dial" assignment For "Softkeys" assignment* *[CH/WX] appears instead of [CHAN], depending on the version. rrPush [EXIT] to exit the Menu screen. • Push [CLEAR] or [BACK] to return to the previous screen. • Dial assignment The Audio volume (VOL), squelch (SQL), channel selection (CHAN) and LCD backlight level (Backlight) functions can be assigned to any one of 4 sequential positions on Dial. Pushing Dial 1 to 4 times sequentially selects the desired function, and rotating Dial adjusts the level or selects a value or number. For example: - VOL is assigned the 1st position, and pushing Dial once selects VOL. The VOL adjust screen is displayed and rotating Dial adjusts the audio volume. - CH is assigned to the 3rd position, and pushing Dial three times selects CH. The channel number is displayed and rotating Dial will select the desired channel. You can assign VOL, SQL, CHAN and Backlight to any one of the 1st, 2nd, 3rd, or 4th sequential positions. Repeatedly pushing Dial sequentially displays all the functions in the order they are assigned, and skips any functions assigned as Not Used. • Softkeys assignment The desired function can be assigned as the softkey function. The assigned function can be used when its key icon is displayed. See page 3 for details of the assignable key functions. wwRotate Dial or push to select the option, and then push [ENT] to set it is displayed next to the selected option. eePush [EXIT] to exit the Menu screen. • Push [CLEAR] or [BACK] to return to the previous screen. • RX Turn the receive Noise Cancel function ON or OFF. OFF : Turns OFF the function. (Default) 1: The Noise Cancel function reduces random noise components in the received signal to approximately one half. 2: The Noise Cancel function reduces random noise components in the received signal to approximately one third. 3: The Noise Cancel function reduces random noise components in the received signal to approximately one tenth. • TX Turn the transmit Noise Cancel function ON or OFF. OFF: Turns OFF the function. (Default) ON: The Noise Cancel function reduces random noise components in the transmitted signal to one third.