Icom IC-M700PRO Instruction Manual

Icom IC-M700PRO Manual

Get Icom IC-M700PRO PDF manuals and user guides View all Icom IC-M700PRO manuals
Add to My Manuals
Save this manual to your list of manuals

Icom IC-M700PRO manual content summary:

  • Icom IC-M700PRO | Instruction Manual - Page 1
    INSTRUCTION MANUAL SSB RADIO TELEPHONE iM700PRO
  • Icom IC-M700PRO | Instruction Manual - Page 2
    INSTRUCTION MANUAL-This manual contains important safety and operating instructions for the IC-M700PRO SSB RADIO TELEPHONE. EXPLICIT DEFINITIONS The explicit definitions described below apply to this instruction manual Icom, Icom Inc. and the Icom logo are registered trademarks of Icom
  • Icom IC-M700PRO | Instruction Manual - Page 3
    -100L ANTENNA MATCHERS ·19 D AT-130 AUTOMATIC ANTENNA TUNER····19 D Non-Icom tuner 19 ■ Mounting 20 D Mounting location 20 D Mounting example 20 D DC power cable fuse 21 D Circuitry fuse 21 7 TROUBLESHOOTING 22 ■ Specifications 23 8 SPECIFICATIONS AND OPTIONS 23 ■ Options 23
  • Icom IC-M700PRO | Instruction Manual - Page 4
    not required for safety purposes. The Restricted Radiotelephone Operator Permit must be posted or be kept with the operator. Only a licensed radio operator may operate a transceiver. However, non-licensed individuals may talk over a transceiver if a licensed operator starts, supervises, and ends the
  • Icom IC-M700PRO | Instruction Manual - Page 5
    IC-M700PRO. MICROPHONE iM 700PRO TX FREQ 2182KHz RESET [ALARM] + [TX FREQ] FOR ALARM TX POWER SPEAKER DIMMER VOLUME ALM RX TX DSC MODE GROUP SSB RADIO the antenna. • Activates only when an optional antenna tuner such as Icom's AT-130 is connected. ☞ NOTE: When selecting "automatic tuning"
  • Icom IC-M700PRO | Instruction Manual - Page 6
    IC-M700PRO. iM 700PRO TX FREQ 2182KHz RESET [ALARM] + [TX FREQ] FOR ALARM TX MICROPHONE POWER SPEAKER DIMMER VOLUME !5 !4 !3 !2 ALM RX TX DSC 0 MODE GROUP SSB RADIO . See the separate KEYPAD OPERATION and CHANNEL LIST instruction sheet for operating details. !2 SQUELCH SWITCH [SQL
  • Icom IC-M700PRO | Instruction Manual - Page 7
    RECEIVE INDICATOR Appears while receiving and when the squelch is open. w TUNE INDICATOR (p. 8) Flashes while the connected antenna tuner, such as Icom's AT-130, is being tuned. • Tuning starts when transmitting on a new frequency or pushing the [TUNE] switch. e TRANSMIT INDICATOR Appears when
  • Icom IC-M700PRO | Instruction Manual - Page 8
    3 SELECTING A CHANNEL/FREQUENCY ■ Memory mode/VFO mode The transceiver has 2 operating modes: memory mode and VFO mode. The memory mode is used to select preprogrammed marine channels in one of the 3 channel groups; The VFO mode is used to select frequencies around preprogrammed channels. Push [CH/
  • Icom IC-M700PRO | Instruction Manual - Page 9
    3 SELECTING A CHANNEL/FREQUENCY D Scan function The scan function allows you to automatically search for signals with a group of channels. There are 2 scan types (selectable in the set mode) as follows: Channel scan ch 2 ch 1 ch 50 ch 3 ch 5 scan is ch 4 cancelled when transmitting Scan
  • Icom IC-M700PRO | Instruction Manual - Page 10
    3 SELECTING A CHANNEL/FREQUENCY ■ Resetting the CPU Under some circumstances, the transceiver's internal CPU may cause erroneous indications on the display. If this happens, reset the CPU as follows: While pushing [ENT] and [0], push [POWER] to turn RX power ON. SIMP • The CPU is reset and
  • Icom IC-M700PRO | Instruction Manual - Page 11
    RECEIVE AND TRANSMIT 4 ■ Basic voice receive and transmit q Check the following in advance: ➥ The microphone is connected. ➥ The [SPEAKER] switch is turned OFF. ➥ The [SQL] switch is turned OFF. ➥ The [CLARITY] control is set to the center position. ➥ The memory mode is selected. • If necessary
  • Icom IC-M700PRO | Instruction Manual - Page 12
    4 RECEIVE AND TRANSMIT ■ Functions for receive D Squelch function The squelch function detects signals with voice components and squelches (mutes) unwanted signals, such as unmodulated beat signals. This provides quiet standby. When you need to receive weak signals, the squelch should be turned OFF
  • Icom IC-M700PRO | Instruction Manual - Page 13
    ) ➥ Semi break-in (automatic transmission with keying) ➥ OFF (manual transmission is necessary before keying) q Connect a CW keyer or an mode (p. 12). ➥ Some transceivers may operate 1.7 kHz higher than the IC-M700PRO's J2B mode, even when the same displayed frequencies are in use. FSK terminal
  • Icom IC-M700PRO | Instruction Manual - Page 14
    tuner control systems for use with an optional Icom antenna tuner. Select the condition, depending on the ] switch, for instant operation. If manual tuning is required, this automatic operation channel scan and channel resume scan search around a user selected channel or search in the band when a
  • Icom IC-M700PRO | Instruction Manual - Page 15
    : 850 Hz FSK normal (default) FSK reverse Full break-in Automatic keying without delay time (default) Semi break-in Automatic keying with delay time OFF Manual transmission necessary for keying 12
  • Icom IC-M700PRO | Instruction Manual - Page 16
    remote control When connecting an external controller, such as a personal computer, 2-digit ID codes are required to access the transceiver. The IC-M700PRO adopts the NMEA0183 format, and uses a "proprietary sentence" for remote control. (11) Remote control input terminal Remote control signals can
  • Icom IC-M700PRO | Instruction Manual - Page 17
    (14) Group B channel inhibit This item allows you to set the number of usable channels in channel group B, up to a maximum of 50 channels. (15) Group C channel inhibit This item allows you to set the number of usable channels in channel group C, up to a maximum of 50 channels. SET MODE 5 Minimum
  • Icom IC-M700PRO | Instruction Manual - Page 18
    AT-130 q rt w u y R CAUTION: NEVER remove the i line fuse from the DC power cable. External speaker q ANTENNA CONNECTOR (p. 19) Connects a 50 ø HF band antenna with a 50 ø matched coaxial cable and a PL-259 plug. w GROUND TERMINAL  IMPORTANT! Connects to a ship's (or vehicle's) ground. See
  • Icom IC-M700PRO | Instruction Manual - Page 19
    6 CONNECTIONS AND INSTALLATION ■ Connector information ACC(1) 4 25 1 3 8 6 7 PIN PIN NAME DESCRIPTION 1 CWK CW and FSK keying input. 2 GND Connects to ground. SPECIFICATIONS Input level: Less than 0.6 V for transmit. Connected in parallel with ACC(2) pin 2. 3 SEND Input/output pin.
  • Icom IC-M700PRO | Instruction Manual - Page 20
    6 CONNECTIONS AND INSTALLATION ■ Connector information (Continued) REMOTE 6 9 1 5 PIN PIN NAME DESCRIPTION 1 MOD+ Modulation input from an external terminal unit. 2 MOD- Coaxial ground for MOD+. 3 AF+ AF detector output for an external terminal unit. 4 AF- Coaxial ground for AF+. 5
  • Icom IC-M700PRO | Instruction Manual - Page 21
    tuner to one ground point, otherwise voltage differences between 2 ground points may cause electrolysis. CAUTION: The IC-M700PRO has a negative ground. NEVER connect the IC-M700PRO to a "positive ground system," otherwise the transceiver will not function. Ground system example Good ground points
  • Icom IC-M700PRO | Instruction Manual - Page 22
    . Antenna wire MN-100/MN-100L D AT-130 AUTOMATIC ANTENNA TUNER IC-M700PRO [KEY] [13.6] [START] [E] AT-130 [E] [13.6] [START] [KEY] To antenna element Coaxial cable D Non-Icom tuner Some non-Icom tuners may be used with the ICM700PRO. Please consult your dealer or marina if you wish to use
  • Icom IC-M700PRO | Instruction Manual - Page 23
    6 CONNECTIONS AND INSTALLATION ■ Mounting R WARNING: NEVER mount the transceiver overhead. The weight of the transceiver is approximately 7.9 kg. (17.4 lb), but its apparent weight will increase several fold due to wave shocks or vibration. The transceiver must be mounted on a flat, hard surface.
  • Icom IC-M700PRO | Instruction Manual - Page 24
    ■ Disassembling the transceiver D Opening the case Follow the case and cover opening procedures shown here when you want to adjust a setting for non-Icom tuner control. q Remove the 9 screws from the rear panel, then remove the rear frame and rear sealing. w Remove the transceiver case. e When
  • Icom IC-M700PRO | Instruction Manual - Page 25
    TROUBLESHOOTING 7 What appears to be equipment malfunction may not be damaging or difficult to solve. Check the following chart before making any adjustments or sending the transceiver to an Icom Service Center. POWER RECEIVE PROBLEM in 2, 11 usual. when manual tuning is selected. the set
  • Icom IC-M700PRO | Instruction Manual - Page 26
    .3 ft Matches the transceiver to a dipole antenna. Covers all HF bands from 1.5 to 30 MHz. 8 m (26 ft.) Icom optional equipment is designed for optimal performance when used with an Icom transceiver. Icom is not responsible for the destruction or damage to an Icom transceiver in the event the Icom
  • Icom IC-M700PRO | Instruction Manual - Page 27
    MEMO 24
  • Icom IC-M700PRO | Instruction Manual - Page 28
    A5472H-1EX-3a Printed in Japan © 1997-2017 Icom Inc. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003 Japan
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
INSTRUCTION MANUAL
SSB RADIO TELEPHONE
iM700PRO