Insignia NS-39DR510NA17 User Manual English - Page 50

Using your Insignia Roku TV, Status light, Standby mode energy savings, Watching broadcast TV

Get Insignia NS-39DR510NA17 PDF manuals and user guides View all Insignia NS-39DR510NA17 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

39" 1080p, 60Hz, LED Roku TV Using your Insignia Roku TV This section provides information on using the day-to-day features of your TV. Status light Your TV has a single status light on the front panel. It goes on and off and blinks in different ways depending on the status of the TV, as shown in the following table: TV condition On (screen is active) Status indicator Off Meaning Screen is indicating that your TV is on. Screensaver (screen is active, except when the Picture Mode is set to Power Saver. Off Power Saver turns off the backlight.) Off (no power) Off Off (standby) Starting up from off state On (receiving update from USB) Remote control command received Powering down to standby mode On Slow pulsing blink until startup completes Slow pulsing blink until update completes Dims on/off once Slow pulsing blink until the TV reaches standby Screen is indicating that your TV is on. Your TV is not connected to power. Your TV is connected to power and ready to use. Your TV is doing something. Your TV is doing something. Your TV has received your command. Your TV is doing something. Standby mode energy savings When you turn off your TV, it may remain in a higher power mode for a few minutes, after which it goes into a very low power standby mode. If you turn on the TV again before it has entered the very low power mode, it turns on immediately. After the TV goes into the lower power standby mode, it takes a bit longer to start up. Watching broadcast TV channels To watch broadcast TV, select the Antenna TV tile in the Home screen. Your TV remembers the last channel you watched and starts with that channel playing. Tip You also can use the /INPUT button on the TV to select Antenna TV, as explained in Side jacks on page 11. Changing channels To change channels, you can do any of the following: • Press the UP arrow to change to the next higher channel. • Press the DOWN arrow to change to the next lower channel. • Press the LEFT arrow to display the channel list, and then press the UP and DOWN arrows to move the highlight through the list one channel at a time. Or press REWIND and FAST FORWARD to move the highlight through the list one page at a time. When you've highlighted the channel you want to watch, press OK. (If you decide you don't want to change channels, press the RIGHT arrow or BACK button). • Press to switch to the previously tuned channel. Note If is not available on your remote control, you can use on the Roku App or the Jump Back button on a universal remote. For more information, see Other devices on page 71. www.insigniaproducts.com 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
45
39" 1080p, 60Hz, LED Roku TV
www.insigniaproducts.com
Using your Insignia Roku TV
This section provides information on using the day-to-day features of your TV.
Status light
Your TV has a single status light on the front panel. It goes on and off and blinks in different ways depending on the
status of the TV, as shown in the following table:
Standby mode energy savings
When you turn off your TV, it may remain in a higher power mode for a few minutes, after which it goes into a very low
power standby mode. If you turn on the TV again before it has entered the very low power mode, it turns on
immediately. After the TV goes into the lower power standby mode, it takes a bit longer to start up.
Watching broadcast TV channels
To watch broadcast TV, select the
Antenna TV
tile in the
Home
screen. Your TV remembers the last channel you
watched and starts with that channel playing.
Changing channels
To change channels, you can do any of the following:
•
Press the
UP
arrow to change to the next higher channel.
•
Press the
DOWN
arrow to change to the next lower channel.
•
Press the
LEFT
arrow to display the channel list, and then press the
UP
and
DOWN
arrows to move the highlight
through the list one channel at a time. Or press
REWIND
and
FAST FORWARD
to move the highlight through the list
one page at a time. When you’ve highlighted the channel you want to watch, press
OK
. (If you decide you don't want
to change channels, press the
RIGHT
arrow or
BACK
button).
• Press
to switch to the previously tuned channel.
TV condition
Status indicator
Meaning
On (screen is active)
Off
Screen is indicating that your TV is on.
Screensaver (screen is active,
except when the
Picture
Mode
is set to
Power Saver
.
Power Saver
turns off the
backlight.)
Off
Screen is indicating that your TV is on.
Off (no power)
Off
Your TV is not connected to power.
Off (standby)
On
Your TV is connected to power and ready
to use.
Starting up from off state
Slow pulsing blink until
startup completes
Your TV is doing something.
On (receiving update from
USB)
Slow pulsing blink until
update completes
Your TV is doing something.
Remote control command
received
Dims on/off once
Your TV has received your command.
Powering down to standby
mode
Slow pulsing blink until
the TV reaches standby
Your TV is doing something.
Tip
You also can use the
/INPUT
button on the TV to select Antenna TV, as explained in
Side jacks
on page
11
.
Note
If
is not available on your remote control, you can use
on the Roku App or the
Jump Back button on a universal remote. For more information, see
Other devices
on
page
71
.