Intel D915PGN Product Guide - Page 27

Installing and Replacing Desktop Board Components, Before You Begin

Get Intel D915PGN - Desktop Board Motherboard PDF manuals and user guides
UPC - 735858178341
View all Intel D915PGN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

2 Installing and Replacing Desktop Board Components This chapter tells you how to: • Install the I/O shield • Install and remove the desktop board • Install and remove a processor and memory • Install and remove a x16 PCI Express card • Connect the IDE and Serial ATA cables • Connect the front panel header • Install the front panel audio and USB solutions • Connect fans and power cables • Connect PCI bus add-in and PCI Express add-in cards • Set the BIOS configuration jumper • Clear passwords • Replace the battery Before You Begin WARNINGS The procedures in this chapter assume familiarity with the general terminology associated with personal computers and with the safety practices and regulatory compliance required for using and modifying electronic equipment. Disconnect the computer from its power source and from any telecommunications links, networks, or modems before performing any of the procedures described in this chapter. Failure to disconnect power, telecommunications links, networks, or modems before you open the computer or perform any procedures can result in personal injury or equipment damage. Some circuitry on the board can continue to operate even though the front panel power button is off. Follow these guidelines before you begin: • Always follow the steps in each procedure in the correct order. • Set up a log to record information about your computer, such as model, serial numbers, installed options, and configuration information. • Electrostatic discharge (ESD) can damage components. Perform the procedures described in this chapter only at an ESD workstation using an antistatic wrist strap and a conductive foam pad. If such a station is not available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the computer chassis. 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
27
2
Installing and Replacing Desktop
Board Components
This chapter tells you how to:
•
Install the I/O shield
•
Install and remove the desktop board
•
Install and remove a processor and memory
•
Install and remove a x16 PCI Express card
•
Connect the IDE and Serial ATA cables
•
Connect the front panel header
•
Install the front panel audio and USB solutions
•
Connect fans and power cables
•
Connect PCI bus add-in and PCI Express add-in cards
•
Set the BIOS configuration jumper
•
Clear passwords
•
Replace the battery
Before You Begin
WARNINGS
The procedures in this chapter assume familiarity with the general terminology associated with
personal computers and with the safety practices and regulatory compliance required for using
and modifying electronic equipment.
Disconnect the computer from its power source and from any telecommunications links,
networks, or modems before performing any of the procedures described in this chapter.
Failure
to disconnect power, telecommunications links, networks, or modems before you open the
computer or perform any procedures can result in personal injury or equipment damage.
Some
circuitry on the board can continue to operate even though the front panel power button is off.
Follow these guidelines before you begin:
•
Always follow the steps in each procedure in the correct order.
•
Set up a log to record information about your computer, such as model, serial numbers,
installed options, and configuration information.
•
Electrostatic discharge (ESD) can damage components.
Perform the procedures described in
this chapter only at an ESD workstation using an antistatic wrist strap and a conductive foam
pad.
If such a station is not available, you can provide some ESD protection by wearing an
antistatic wrist strap and attaching it to a metal part of the computer chassis.