Intel R2000LH2/LT2 Service Guide - Page 35

Removing and Installing the PCI Riser Assembly

Get Intel R2000LH2/LT2 PDF manuals and user guides View all Intel R2000LH2/LT2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Hardware Installations and Upgrades Removing and Installing the PCI Riser Assembly Before removing or installing the PCI riser assembly, please make sure following steps are performed. 1. Ensure the AC power cord(s) are disconnected from the system. 2. Remove the system cover. For instructions, see Removing the System Cover. Removing the PCI Riser Assembly 1. Disconnect any cables attached to any add-in cards, pull up the release lever (see letter A). 2. Grasp the riser assembly with both hands and pull up to remove from system (see letter B). Figure 31. Removing the PCI Riser Assembly Warning: Place the riser assembly upside down or sideway to avoid damage to the riser card connector. Do one of the following: - If you need to add or replace a PCI add-in card, see Installing and Removing a PCI Add-in Card. - If you removed the PCI riser assembly for another procedure, continue with that procedure. Installing the PCI Riser Assembly 1. Position the riser card connector edge over the server board riser socket (see letter A). 2. Press down the release lever to install the riser assembly into the riser socket (see letter B). 3. Push on the board edge above the connector to ensure the connector is seated. Figure 32. Installing the PCI Riser Assembly Intel® Server System R2000LH2/LT2 Service Guide 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Hardware Installations and Upgrades
Intel
®
Server System R2000LH2/LT2 Service Guide
23
Removing and Installing the PCI Riser Assembly
Before removing or installing the PCI riser assembly, please make sure following steps are performed.
1.
Ensure the AC power cord(s) are disconnected from the system.
2.
Remove the system cover. For instructions, see
Removing the System Cover
.
Removing the PCI Riser Assembly
1.
Disconnect any cables attached to any add-in cards, pull up the release lever (see letter
A
).
2.
Grasp the riser assembly with both hands and pull up to remove from system (see letter
B
).
Figure 31. Removing the PCI Riser Assembly
Warning:
Place the riser assembly upside down or sideway to avoid damage to the riser card
connector.
Do one of the following:
—
If you need to add or replace a PCI add-in card, see
Installing and Removing a PCI Add-in Card
.
—
If you removed the PCI riser assembly for another procedure, continue with that procedure.
Installing the PCI Riser Assembly
1.
Position the riser card connector edge over the server board riser socket (see letter
A
).
2.
Press down the release lever to install the riser assembly into the riser socket (see letter
B
).
3.
Push on the board edge above the connector to ensure the connector is seated.
Figure 32. Installing the PCI Riser Assembly