Intel SC5275-E User Guide - Page 37

Install the Server Board, Start User's Guide. - 11

Get Intel SC5275-E - Entry Server Chassis PDF manuals and user guides
UPC - 735858171168
View all Intel SC5275-E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

2 Setting Up the Chassis Install the Server Board 1. Remove and save the four screws that secure the drive cage to the chassis. Two screws are at the front of the chassis and two are at the side of it. 2. Slide the drive cage out of the chassis. You may need to push the cage out from the inside of the chassis. TP00062 Figure 11. Removing a Drive Cage 3. For additional information, read and follow the instructions provided with the server board Quick Start User's Guide. These instructions will guide you through preparing the board, processors, and memory for installation. 4. Tilt the board into the chassis I/O connector end first. Make sure the I/O connectors protrude through the I/O shield at the back of the chassis. 5. Attach the board to the two snap stand-offs at the front of the chassis. 6. Insert screws loosely through the server board mounting holes and into the threaded standoffs. 7. Make sure the board is properly seated and then tighten the screws firmly, starting with the screws at the center of the board. Intel® Entry Server Chassis SC5275-E User Guide 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
2
Setting Up the Chassis
Intel® Entry Server Chassis SC5275-E User Guide
19
Install the Server Board
1.
Remove and save the four screws that secure the drive cage to the chassis.
Two screws are at the
front of the chassis and two are at the side of it.
2.
Slide the drive cage out of the chassis.
You may need to push the cage out from the inside of the
chassis.
TP00062
Figure 11.
Removing a Drive Cage
3.
For additional information, read and follow the instructions provided with the server board Quick
Start User’s Guide.
These instructions will guide you through preparing the board, processors,
and memory for installation.
4.
Tilt the board into the chassis I/O connector end first.
Make sure the I/O connectors protrude
through the I/O shield at the back of the chassis.
5.
Attach the board to the two snap stand-offs at the front of the chassis.
6.
Insert screws loosely through the server board mounting holes and into the threaded standoffs.
7.
Make sure the board is properly seated and then tighten the screws firmly, starting with the
screws at the center of the board.