Intel SE7500WV2 Product Guide - Page 34

Installing Peripherals

Get Intel SE7500WV2 - Server Chassis - SR2300 PDF manuals and user guides
UPC - 735858157049
View all Intel SE7500WV2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

3. If it isn't installed, install the power supply air baffle. All cables from the power supply should route through the notch in the bottom of the baffle. A B OM14582 Figure 21. Installing the Power Supply Air Baffle 4. Connect the SCSI cable to the SCSI connector on the server board. Route the cable between the memory connectors and the full height PCI riser, through the clips on the side of the processor duct, through the notch in the top of the power supply air baffle, to the connector on the backplane board. ✏ NOTE It may be easier to route the SCSI cable after the full length PCI riser card is installed. 5. Ensure that the front panel cable is connected to the front panel board, routed over USB cable to the backplane, and connected to the matching connector. Installing Peripherals Peripherals and add-in cards are not included in your system and must be purchased separately. The following sections describe how to install PCI add-in cards, hard disk drives, a DVD/CD-ROM drive/floppy disk drive, and a tape drive. 34 Intel SR2300 Chassis Subassembly Product Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
34
Intel SR2300 Chassis Subassembly Product Guide
3. If it isn
’
t installed, install the power supply air baffle.
All cables from the power supply should
route through the notch in the bottom of the baffle.
OM14582
B
A
Figure 21.
Installing the Power Supply Air Baffle
4.
Connect the SCSI cable to the SCSI connector on the server board.
Route the cable between
the memory connectors and the full height PCI riser, through the clips on the side of the
processor duct, through the notch in the top of the power supply air baffle, to the connector on
the backplane board.
✏
NOTE
It may be easier to route the SCSI cable after the full length PCI riser card is
installed.
5.
Ensure that the front panel cable is connected to the front panel board, routed over USB cable
to the backplane, and connected to the matching connector.
Installing Peripherals
Peripherals and add-in cards are not included in your system and must be purchased separately.
The following sections describe how to install PCI add-in cards, hard disk drives, a DVD/CD-ROM
drive/floppy disk drive, and a tape drive.