Intel SR1500AL User Guide - Page 61

Installing and Removing a Hot-swap Hard Drive

Get Intel SR1500AL - Server System - 0 MB RAM PDF manuals and user guides View all Intel SR1500AL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

TP02205 Figure 29. Installing the Small Air Baffle 3. Install the server system cover. For instructions, see "Installing the System Cover". 4. Plug all peripheral devices and the AC power cable(s) into the server. Installing and Removing a Hot-swap Hard Drive Up to three hot-swap SAS or SATA drives can be installed. Cautions: If you install less than three drives or devices, the empty drive bays must be occupied by carriers with baffles to maintain proper system cooling. To avoid possible damage to your server system, do not use older style drive carriers. Note: The server system does not support all hard drives. See "Server System References" for an Internet link to a list of supported hardware. Installing a SAS or SATA Hot-swap Hard Disk Drive 1. Remove the front bezel if it is installed. For instructions, see "Removing the Front Bezel". 2. Open the latch at the front of the hard drive carrier. See letter "A" in the figure below. 3. Pull out on the black lever and slide the carrier from the server system. See letter "B" in the figure below. Intel® Server System SR1500AL User's Guide 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
Intel
®
Server System SR1500AL User’s Guide
39
Figure 29. Installing the Small Air Baffle
3.
Install the server system cover. For instructions, see
“Installing the System Cover”
.
4.
Plug all peripheral devices and the AC power cable(s) into the server.
Installing and Removing a Hot-swap Hard Drive
Up to three hot-swap SAS or SATA drives can be installed.
Cautions:
If you install less than three drives or devices, the empty drive bays must be occupied by
carriers with baffles to maintain proper system cooling.
To avoid possible damage to your server system, do not use older style drive carriers.
Note:
The server system does not support all hard drives. See
“Server System References“
for
an Internet link to a list of supported hardware.
Installing a SAS or SATA Hot-swap Hard Disk Drive
1.
Remove the front bezel if it is installed. For instructions, see
“Removing the Front
Bezel”
.
2.
Open the latch at the front of the hard drive carrier. See letter "A" in the figure
below.
3.
Pull out on the black lever and slide the carrier from the server system. See letter
"B" in the figure below.
TP02205