Invacare M94 Owners Manual - Page 39

Remote On/Off Switch, Mode Switch, Memory Card Slot

Get Invacare M94 PDF manuals and user guides View all Invacare M94 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

SECTION 5-WHEELCHAIR OPERATION Remote On/Off Switch The remote On/Off switch input is located at the rear of the joystick on the right side and allows the power switch to be operated by an ability switch (normally open momentary switch with mono plug). To use the remote On/Off feature, the Drive Select/On/Off switch must be in the On position. Each activation of the ability switch will alternately turn the joystick On or Off. Mode Switch NOTE: For this procedure, refer to FIGURE 5.4 on page 35. The mode switch is used to select the operating mode for the wheelchair. The mode switch is located on the joystick. A mode switch is needed whenever any of the following operating modes are programmed: • Environmental Controls (ECU 1, ECU 2, ECU 3, ECU 4)* • 3 Speed Mode in Digital 3 Speed (Slow, Medium, Full) • Latched Modes • Sleep Mode • RIM Mode* • Remote Drive Selection Mode* • Tilt/Recline Mode* • Information Center Display Selection (does not require Reset activation at power up) If any of the above modes are selected, the control will require activation of the switch immediately after the power switch is turned On in order to enter the drive mode. The second line of the LCD will display ‐ PRESS RESET. *NOTE: In these modes, Standby Select allows the reset switch to be bypassed for users unable to activate the switch. Memory Card Slot The memory card slot is used with the basic or professional memory card for saving or reading wheelchair parameters. Part No 1122145 39 Pronto® M94™

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
SECTION 5—WHEELCHAIR OPERATION
Part No 1122145
39
Pronto® M94™
Remote On/Off Switch
The remote On/Off switch input is located at the rear of the joystick on the right side and
allows the power switch to be operated by an ability switch (normally open momentary
switch with mono plug). To use the remote On/Off feature, the Drive Select/On/Off switch
must be in the On position. Each activation of the ability switch will alternately turn the
joystick On or Off.
Mode Switch
NOTE: For this procedure, refer to FIGURE 5.4 on page 35.
The mode switch is used to select the operating mode for the wheelchair. The mode
switch is located on the joystick. A mode switch is needed whenever any of the following
operating modes are programmed:
•
Environmental Controls (ECU 1, ECU 2, ECU 3, ECU 4)*
•
3 Speed Mode in Digital 3 Speed (Slow, Medium, Full)
•
Latched Modes
•
Sleep Mode
•
RIM Mode*
•
Remote Drive Selection Mode*
•
Tilt/Recline Mode*
•
Information Center Display Selection (does not require Reset activation at power up)
If any of the above modes are selected, the control will require activation of the switch
immediately after the power switch is turned On in order to enter the drive mode. The
second line of the LCD will display
‐
PRESS RESET.
*NOTE: In these modes, Standby Select allows the reset switch to be bypassed for users unable to
activate the switch.
Memory Card Slot
The memory card slot is used with the basic or professional memory card for saving or
reading wheelchair parameters.