JVC BR-DV3000UB BR-DV3000U Pro-DV recorder 71 page instruction manual - Page 13
Alarm display
UPC - 046838325595
View all JVC BR-DV3000UB manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 13 highlights
ON-SCREEN DISPLAY - Alarm display - Ⅵ Alarm display : Alarm messages are displayed as shown below, when an operation error has occurred or when the unit is in a poor condition for operation. E.g., dirty head. 3 2K CH- 1 / 2 S P000m i n A HEAD CL EAN I NG REQU I RED ! B NO DV S I GNA L 04 / 01 / 02 F11 : 20 : 00 STANDBY-OF TCR 0 2 : 0 0 : 0 0 : 0 Ⅵ Display at position A : Displays which show the state of the unit (and which are not set via the DISPLAY mode) continues to be displayed here until the conditions are rectified. Display LOW VOLTAGE Contents The voltage of the DC input power is low. Continued operation will bring the unit to the Operate OFF mode. HEAD CLEANING REQUIRED! The video head is dirty. Please clean it with the dedicated head-cleaning tape. (☞ Page 8) If the head is clogged, it will be detected in the PLAYBACK mode and displayed. When the unit enters the STOP mode or the cassette is ejected, the display goes off. OVERHEATING! The temperature inside the unit has exceeded the regulated value. Please disconnect the power and place the unit in a cool place. If this message is displayed again, damage may have occurred. Please consult with your JVC-authorized service agent. Ⅵ Display at position B : Messages indicating operation errors are displayed for about 3 seconds. They are displayed when the DISPLAY mode is ON or AUTO. Display INVALID TAPE! Contents Data tapes for PC use or DVC PRO tapes has been inserted. The cassette will be ejected. LP TAPE! The user attempts to play back a tape recorded in the LP mode. This unit cannot record or play in the LP mode. NO DV SIGNAL The user attempts to record without DV signal input. 22 Display COPY INHIBIT REC INHIBIT A. DUB INHIBIT (REC TAB) A. DUB INHIBIT (48K) A. DUB INHIBIT (LP) A. DUB INHIBIT (BLANK) A. DUB INHIBIT (DV) A. DUB INHIBIT (NTSC/PAL) A. DUB INHIBIT (DVCAM) OPERATION LOCK Contents The user attempts to record signals protected with the copy guard. The user attempts to record on a write protected cassette tape. (The rear slide is pushed to SAVE.) The user attempts to perform audio dubbing on a write protected cassette tape. (The rear slide is pushed to SAVE.) This message is displayed when audio dubbing is attempted under the following conditions: • The AUDIO MODE item of the AUDIO/VIDEO menu is set to 48k. • The tape is recorded with a sample frequency of 48kHz. The user attempts to perform audio dubbing on a tape recorded in the LP mode. The user attempts to perform audio dubbing on a blank tape. The user attempts to perform audio dubbing during DV signal input. (The INPUT SEL switch is set to DV) This message is displayed when the signal system is changed during audio dubbing (NTSC or PAL). The user attempts to perform audio dubbing on a DVCAM format tape. This message is displayed when a button on the unit is pressed while the OPERATION LOCK function is engaged (ie, the OPERATION item of the SYSTEM (2/2) menu is set as ON). Ⅵ Warning display : When anomalies occur in the VTR, warning messages with error codes will be displayed. 3 2K CH- 1 / 2 S P000m i n WARN I NG 7 0 0 1 DRUM MOTOR F A I L URE 04 / 01 / 02 11 : 20 : 00 S T ANDBY -OF F TCR 0 2 : 0 0 : 0 0 : 0 0 Warning display For details, please refer to page 66, "Warning Display". 23