JVC DR-M100S Instruction Manual - Page 39

Manual Timer Programming You can programme this unit to timer record as many as 8 programmes up to 30 days in advance. If you do not know the PlusCode number for the programme you wish to record, use the following procedure to set your unit to timer record the programme. ● Turn on the unit. ● Turn on the TV and select an input mode such as EXT1. ● Make sure that the unit's built-in clock is set properly. TIMER j PROG Selection Keys (FGDE) ENTER 1 Load a recordable disc. ● For details, refer to APlacing A DiscB (A pg. 9). 2 Press PROG to display the APROGRAMME CHECKB screen. ● When APROGRAMME FULL DELETE UNWANTED TIMER PROGRAMME CHECK DATE START-STOP TV PROG DAILY/WEEKLY VPS/PDC REC MODE 05/07 SAT 19:00 - 20:00 44 WEEKLY ON SP 10/07 THU 22:00 - 22:30 10 ON XP 11/07 FRI 13:30 - 14:00 26 OFF LP 11/07 FRI 16:00 - 17:00 33 OFF LP NEW TIMER PROGRAMME PROGRAMMEB appears on the TV screen, you need to cancel some of EXIT the reserved PROG programmes. DISC TIMER PRGM OK SELECT WITH [CURSORS] SELECT THEN PRESS [ENTER] 3 Press selection keys repeatedly to select TIMER PROGRAMME ANEW TIMER PROGRAMMEB, then press ENTER. DATE 05/07 SAT START 20:00 STOP 20:30 TV PROG VTM 10 4 Press selection keys to DAILY/WEEKLY VPS/PDC REC MODE set the desired date NAME OFF LP (ADATEB), then press E. 5 Press selection keys to EXIT set the desired start PROG CONFIRM SET TIMER PROGRAMMING WITH [CURSORS] SELECT THEN PRESS [ENTER] time (ASTARTB), then press E. ● Each press of F G increases/decreases the start time in 1 minute interval. ● To increase/decrease the start time in 30 minutes interval, press and hold F G. TIMER RECORDING EN 39 6 Press selection keys to set the desired stop time (ASTOPB), then press E. ● Each press of F G increases/decreases the stop time in 1 minute interval. ● To increase/decrease the stop time in 30 minutes interval, press and hold F G. 7 Press selection keys to set the desired channel (ATV PROGB), then press E. 8 Set the other recording options as required. ● Refer to step 6 in AVIDEO Plus+ Timer ProgrammingB (A pg. 38). 9 Press ENTER to access the Programme Confirmation screen. 10 Press ENTER to complete the timer programming. ● To programme another timer, repeat steps 2 - 10. 11 Press TIMERj to engage the unit's timer mode. ● The unit turns off automatically and j appears on the front display panel. ● To disengage the timer mode, press TIMERj again. NOTES: ● When two successive programmes are recorded with the AManual Timer ProgrammingB function, the ending of the first programme or the beginning of the second programme may not be recorded. ● If the copy limited programme is received during timer recording, the unit enters Record Pause mode. Recording starts again if it is switched to a recordable broadcast during the time you programmed. Satellite Receiver Users To record a satellite broadcast using Manual Timer Programming: A Perform Manual Timer Programming. B Set the satellite receiver to the appropriate channel for recording. ● Leave the satellite receiver's power on. VPS/PDC Recording Now available from some TV stations, PDC (Programme Delivery Control) and VPS (Video Programme System) are services designed to assure safe, accurate timer recording. With this system, special code signals are transmitted together with the audio/video signals. These code signals control your unit and have precedence over the advertised times you may have preset into the timer. This means that your unit will start and stop recording when the preset TV programmes actually start and end^even if the broadcast time of a preset TV programme is changed from what has been advertised. PDC is currently available nationally on BBC1, BBC2, Ch.4 and Ch.5, except from a few small relay transmitters. Ch.3 operates a PDC service in some areas. All channels intend to offer this service in due course. Check your TV programme listing guide for latest information. If the channel you intend to record does not offer a PDC service your unit will not start recording if PDC has been selected. Be sure to set PDC to AOFFB if PDC is not available on your selected channel. (See step 6 on page 38.). NOTES: ● When you use Manual Timer Programming, set the start time (VPS or PDC time) exactly as advertised in the TV listing. A different time than advertised will result in no recording. ● VPS/PDC recording is also possible via the [L-1 IN/OUT] connector.