JVC TK-C1530U Instructions - Page 18

System Example continued, Setup, Precautions when using RM-P2580E

Get JVC TK-C1530U - CCTV Camera PDF manuals and user guides
UPC - 046838027925
View all JVC TK-C1530U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Setup System Example (continued) Precautions when using RM-P2580E: When operating a system using the RM-P2580E, several cameras (up to 16) can be connected and used on one control signal cable. Consequently, an incorrect switch setting on just a single camera will cause the entire system to work incorrectly. Confirm switch settings on the monitor screen using the following methods. 1. Confirm that the image from the camera to be checked is displayed on the monitor. 2. Turn ON the power of the camera to be checked. The image is displayed on the monitor screen as shown below. (When MACHINE ID is set to A05B) PROTOCOL : DUPLEX ID-05 Confirm that ADUPLEXB is displayed Check whether the ID is correct 3. Confirm that ADUPLEXB is displayed and that the ID number is correct. Memo: ● The number should be the same as the number of the VIDEO INPUT terminal on the back panel of the RM-P2580E connecting the camera to be checked. 4. If the number is wrong, set the MACHINE ID again. Memo: ● When controlling this camera with any system except the RM-P2580E, perform proper settings using switches and menu screens according to the system used. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
18
Setup
Memo:
●
When controlling this camera with any system except the RM-P2580E,
perform proper settings using switches and menu screens according to the
system used.
System Example (continued)
Precautions when using RM-P2580E:
When operating a system using the RM-P2580E, several cameras (up to
16) can be connected and used on one control signal cable. Consequently,
an incorrect switch setting on just a single camera will cause the entire
system to work incorrectly.
Confirm switch settings on the monitor screen using the following methods.
1.
Confirm that the image from the camera to be checked is displayed
on the monitor.
2.
Turn ON the power of the camera to be checked.
The image is displayed on the monitor screen as shown below.
(When MACHINE ID is set to
A
05
B
)
3.
Confirm that
A
DUPLEX
B
is displayed and that the ID number is
correct.
Memo:
●
The number should be the same as the number of the VIDEO
INPUT terminal on the back panel of the RM-P2580E connecting the
camera to be checked.
4.
If the number is wrong, set the MACHINE ID again.
PROTOCOL : DUPLEX
ID-05
Confirm that
A
DUPLEX
B
is displayed
Check whether the ID is correct