JVC TK-C1530U Instructions - Page 27

Fall Prevention

Get JVC TK-C1530U - CCTV Camera PDF manuals and user guides
UPC - 046838027925
View all JVC TK-C1530U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

1. Remove the camera-mounting bracket fastening screws (x2). The camera-mounting bracket is removed from the camera. 2. Mounting the camera-mounting bracket on top of the camera 3. Mounting the camera onto a fixer, pan/tilt unit and the like Note: ● Use a camera-mounting screw with a length shorter than 7 mm from the camera-mounting face. Do not use a screw that is longer than the specified length. It may damage the internal parts. ● To mount the camera-mounting bracket on top of the camera, use the screw holes on the back panel. Fall Prevention Use the black mounting screw on the back of the camera to install the fall prevention wire 6mm 2mm M3 x 6mm VIDEOUTO Fall Prevention Wire Precautions regarding fall prevention ● Special attention is required when installing the camera to the wall or ceiling. You should not engage in the installation work yourself. Ask a professional to do the job, since the fall of the camera can result in injuries and accidents. ● When installing the camera on a fixer, pan/tilt unit and the like, make sure to install it firmly using a rotation-preventive hole to prevent fall. ● To prevent fall, connect the camera to a section with sufficient strength (ceiling slab or channel) using a fall prevention wire. ● Pay attention to the length, strength, routing and material (insulation properties) of the fall prevention wire used. ● Use the black screw (M3 x 6 mm) on the back of the camera for the installation of the fall prevention wire. Using other screws of different sizes may damage the inside. 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
27
1.
Remove the camera-mounting bracket fastening screws (x2).
The camera-mounting bracket is removed from the camera.
2.
Mounting the camera-mounting bracket on top of the camera
3.
Mounting the camera onto a fixer, pan/tilt unit and the like
Note:
●
Use a camera-mounting screw with a length shorter than 7 mm from the
camera-mounting face. Do not use a screw that is longer than the specified
length. It may damage the internal parts.
●
To mount the camera-mounting bracket on top of the camera, use the
screw holes on the back panel.
Fall Prevention
Use the black mounting screw on the back of the camera to install the fall
prevention wire
VIDEO O
UT
2mm
6mm
M3 x 6mm
Fall Prevention Wire
Precautions regarding fall prevention
●
Special attention is required when installing the camera to the wall or
ceiling. You should not engage in the installation work yourself. Ask a
professional to do the job, since the fall of the camera can result in
injuries and accidents.
●
When installing the camera on a fixer, pan/tilt unit and the like, make
sure to install it firmly using a rotation-preventive hole to prevent fall.
●
To prevent fall, connect the camera to a section with sufficient strength
(ceiling slab or channel) using a fall prevention wire.
●
Pay attention to the length, strength, routing and material (insulation
properties) of the fall prevention wire used.
●
Use the black screw (M3 x 6 mm) on the back of the camera for the
installation of the fall prevention wire. Using other screws of different
sizes may damage the inside.