Kenmore 2029319 Use and Care Manual - Page 17

Always, followallsafety, precautions, whenperforming, maintenance, onthePower-Mate

Get Kenmore 2029319 - Canister Vacuum PDF manuals and user guides
UPC - 037988771011
View all Kenmore 2029319 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

AlwayfsollowallsafetpyrecautiownhsenperformimngaintenanocnethePower-Mate i i i i i lu uluiJllUtlrltlruJJJHlluluuur, ,d WARNING Electrical Shock Or Personal Injury Hazard° Disconnect electrical supply before performing maintenance to the vacuum cleaner, Failure to do so could result in electrical shock or personal injury from vacuum cleaner suddenly starting° I CHA.O,.OA,.NOO.O'TATO" TO REMOVE BELT m REPLACE BELT _,_F" _,._. dMoawten upside 2. Unscrew two (2) motor drive, then over beltpath., '%_y_f ..=iJ_\_" _.__ 'y Mo%r ._ _ screwsP°werc'oMvaetre latches up Latch Latches _V'\__End Cap PBaeli- NOTE: See PARTS AND FEATURES for Belt number 2, Place agitator assembly back into PoweFMate 4.,To remove cover, grasp the sides and pull out, 3oLine up front of cover and base, Rest cover on front edge of base as shown. Cover Base and remove worn belt, End Cap 6. Check and clean end cap areas. See TO CLEAN AGITATOR section and AGITATOR ASSEMBLY illustration for picture of complete agitator assembly. 4_lde _'__, \- Side Latch 7-"_ .V Rear Latches 4oRotate cover back Press cover firmly untif and rear latches snap into place Make sure there is no gap between the cover and base 5, Turn Power-Mate upside down and replace two (2) cover screws 'I7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
Always
followallsafety
precautions
whenperforming
maintenance
onthePower-Mate
i
i
ii
i lu
uluiJllUtlrltlruJJJHlluluuur,
,d WARNING
Electrical
Shock
Or
Personal
Injury Hazard°
Disconnect
electrical
supply
before
performing
maintenance
to the
vacuum
cleaner,
Failure to do so
could
result
in
electrical
shock
or personal
injury
from vacuum
cleaner
suddenly
starting°
I
CHA.O,.OANO.O'TATO"
,.O
TO REMOVE
BELT
m REPLACE BELT
Mate
upside
motor drive,
_,_F"
down
_,._.
then over
'%_y_f
..=iJ_\_"
2. Unscrew two
(2)
belt
path.,
_.__
'y
Mo%r
._
_
screwsP°wer'Mate
cover
_V'\__End Cap PBaeli-
NOTE: See
PARTS AND
FEATURES
for
Belt number
latches up
Latch
Latches
andremove
worn belt,
4.,To remove cover,
grasp the sides and
pull out,
End
Cap
6. Check and clean end cap areas. See TO
CLEAN AGITATOR section and AGITATOR
ASSEMBLY
illustration for picture of
complete agitator assembly.
2, Place agitator
assembly back
into PoweFMate
3o
Line
up
front
of cover and
base, Rest
cover on front
edge of base as
shown.
Cover
Base
4oRotate cover
back Press
'_--'----____,_..
cover firmly untif
___/=:_.._:4_lde
and rear
_'__,
7-"_
latches snap into
\
-
.V
place
Side
Rear
Latch
Latches
Make sure there is
no
gap between the
cover and base
5,
Turn Power-Mate upside down and
replace
two
(2) cover screws
'I7