Kenmore 2029914 Use and Care Manual - Page 24

See Belt Changing

Get Kenmore 2029914 - Canister Vacuum PDF manuals and user guides View all Kenmore 2029914 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Review this table to find do-it-yourself solutions for minor performance problems, Any other service needed should be performed by a Sears or other qualified service agent WARNING Always turn off and unplug vacuum cleaner before performing maintenance to the vacuum cleaner. Failure to do so could result in electrical shock or personal injury° Vacuum cleaner won't starL t,, Unplugged at wall outlet 2., Tripped circuitbreaker/blown fuse at householdservice panel, 3. Loose hose electrical connections 1o Plug in firmly, push ON/OFF switch to on 2. Reset circuit breaker or replace fuse 3, Reconnect hose ends,, Poor job of dirt pick-up,, to Full or clogged dust bag 2_ Clogged airflow passages. 3o Dirty fillers. 4_ Wrong p_leheight setting. 5. Wrong power level selected 6_ Hole in hose. 7o Worn PowerMata agitator 8o Worn or broken belt 9. Dirty agitator or end caps. Canister hood open ti,. Tripped overload protectorin PewerMate Change bag 2. Clear airflow passages 3, Change fillers,, 4, Adjust setting 5, Adjust control 6- Replace hose. 7. Change agitator. 8&9. See BELT CHANGING AND AGITATOR CLEANING 10. Close and talch hood 11. Remove any items lhat may be caught or jammed, lhen reset If vacuum cleaner starts and stops again, clean agitator and end caps, then reset, Vacuum cleaner starts but shuts off. 1. Hose orhood electrical connections, 2. Tripped overload protectorin PowerMate 3. Tripped thermal protector in canister. 1,, Check connections, reconnect hose ends 2o Remove any items that may be caught or jammed, then reset If vacuum cleaner starts and stops again, clean agitatorand end caps, then reset. 3,, See PERFORMANCE FEATURES "Thermal Prolector" PowerMate will not run when attached° 1. PowerMate connections unplugged, 2. Worn or broken bell:, 3_ Didy agitator or end caps 4,, Tripped overload protectorin PowerMate 5. Switch not in CARPET posilion, I,, Plug in firmly 2 & 3. See BELT CHANGING AND AGITATOR CLEANING,, 4. Remove any items that may be caught or jammed, then reset If vacuum cleaner starts and stops again, clean agitator and end caps, lhen reset, 5. Move switch to CARPET position, 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
Review
this
table
to
find
do-it-yourself
solutions
for minor
performance
problems,
Any other
service
needed
should
be performed
by a Sears
or other
qualified
service
agent
WARNING
Always
turn
off
and
unplug
vacuum
cleaner
before
performing
maintenance
to
the
vacuum
cleaner.
Failure
to
do
so
could
result
in
electrical
shock
or personal
injury°
Vacuum cleaner won't
starL
t,, Unplugged at
wall
outlet
2.,
Tripped
circuit
breaker/blown
fuse
at
household
service panel,
3. Loose hose electrical
connections
Poor job
of
dirt
to
pick-up,,
2_
3o
4_
5.
6_
7o
8o
9.
ti,.
Vacuum cleaner
starts
but shuts
off.
Full or clogged dust
bag
Clogged airflow passages.
Dirty fillers.
Wrong p_le
height
setting.
Wrong power level selected
Hole
in hose.
Worn PowerMata agitator
Worn or broken belt
Dirty agitator or end caps.
Canister hood open
Tripped overload
protectorin
PewerMate
1.
Hose
or
hood electrical
connections,
2.
Tripped overload
protectorin
PowerMate
3.
Tripped
thermalprotector
in canister.
1o
Plug in firmly, push ON/OFF switch
to on
2. Reset circuit breaker
or
replace fuse
3, Reconnect hose ends,,
2.
3,
4,
5,
6-
7.
8&9.
10.
11.
Change bag
Clear airflow passages
Change fillers,,
Adjust setting
Adjust control
Replace hose.
Change agitator.
See BELT CHANGING AND
AGITATOR CLEANING
Close and talch hood
Remove
any
items lhat may be
caught or jammed, lhen reset
If
vacuum cleaner starts and stops
again, clean agitator
and
end caps,
then
reset,
1,,
Check connections, reconnect hose
ends
2o
Remove any items that may be
caught or jammed,
then
reset
If
vacuum cleaner starts and stops
again, clean
agitatorand
end caps,
then reset.
3,, See PERFORMANCE FEATURES -
"Thermal Prolector"
PowerMate
will
not
run
when
attached°
1.
PowerMate connections
unplugged,
2.
Worn or broken bell:,
3_
Didy agitator or end caps
4,, Tripped overload
protector
in
PowerMate
5.
Switch not
in
CARPET posilion,
I,, Plug in firmly
2 & 3.
See BELT
CHANGING
AND
AGITATOR
CLEANING,,
4. Remove any items that may be
caught or jammed,
then
reset
If
vacuum cleaner starts and stops
again, clean agitator and
end
caps,
lhen reset,
5. Move switch to
CARPET
position,
24