Kenmore 4044 Use and Care Guide - Page 29

SERVICE, cont.

Get Kenmore 4044 - 4.2 cu. Ft. Front-Load Washer PDF manuals and user guides View all Kenmore 4044 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

BEFORE CALLING FOR SERVICE (cont.) The display shows: I Check if... Loadis too small. Load is out of balance. uC_-_ Then... Add 1 or 2 similar items to help balance the load. Pause the cycle and redistribute the load after the door unlocks. The washer has an imbalance detection and correction system. If individual heavy articles are loaded (bath mat, bath robe, etc.) and the imbalance is too great, the washer will make several attempts to restart the spin cycle. If an imbalance is still detected, the washer wilt stop and the error code wilt be displayed. The display shows: H C Check if... Then... i Controt error. I i Uagnapitnu.gIfththeewearrsohrerreaanpdpewaarist,6c0alsl efocrosnedrsv.icRee.connect power and try [ The display shows: I Check if... _-Cb-_- i Water level is too high due to a faulty water valve. Then... i Close the water taps, unplug the washer, and call for service, i The display shows: I Check if... _-Cr_J- The water level sensor is not working correctly. The display shows: m Check if... Ls _F2 Then... Close the water taps, unplug the washer, and call for service. [ I Then... I I trihpepremda. t overload protection circuit in the motor has been i Athletonwrethsetawrtathsehecrytcoles.taIfntdhefoLrE30ermroirnucotedsetopearlsloiswtst,hceamll footrosr etorvcicoeo.t; [ The display shows: I Check if... PF A power failure has occurred. Then... If the power to the washer has been interrupted during a cycle, the "PF" error code wilt be displayed the next time the washer is turned ON. This wilt alert you to the fact that the previous cycle may not have been completed. Select any cycle to clear the error code and use the washer. 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
BEFORE
CALLING
FOR
SERVICE
(cont.)
The display shows:
I
uC_
_-
Check if...
Then...
Load
is too small.
Add 1 or 2 similar items to help balance the load.
Load is out of balance.
Pause the cycle and redistribute the load after the door unlocks.
The washer has an imbalance detection and correction system. If
individual heavy articles are loaded (bath mat, bath robe, etc.) and
the imbalance is too great, the washer will make several attempts to
restart the spin cycle. If an imbalance is still detected, the washer wilt
stop and the error code wilt be displayed.
The display shows:
H
Check if...
i
Controt error.
C
The display shows:
I
_-Cb-_-
Check if...
Then...
i
Unptug the
washer
and wait 60 seconds. Reconnect power and try
[
again. If the error reappears, call for service.
I
Then...
i
Water level is too high due to a faulty water valve.
i
Close the water taps, unplug the washer, and call for service,
i
The display shows:
I
_-Cr_J-
Check if...
The water level sensor is not working correctly.
Then...
Close the water taps, unplug the washer, and call for service.
[
I
m
s
F
The display shows:
L
_2
Check if...
I
hermat overload protection circuit in the motor has been
tripped.
The display shows:
I
PF
Check if...
Then...
i
Altow the
washer
to stand for 30 minutes to allow the motor to coot;
[
then restart the cycle. If the LE error code persists, call for service.
I
Then...
A power failure has occurred.
If the power to the washer has been interrupted during a cycle, the
"PF" error code wilt be displayed the next time the washer is turned
ON. This wilt alert you to the fact that the previous cycle may not
have been completed. Select any cycle to clear the error code and
use the washer.
29