Kenmore 9746 Installation Instructions - Page 1
Kenmore 9746 - 30 in. Electric Range Manual
View all Kenmore 9746 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. Clearances and Dimensions 1. Provide adequate clearances between the range and adjacent combustible surfaces. 2. LocationmCheck location where the ranqe will be installed. Check for proper electrical supply, and the stability of the floor. 3. Dimensions that are shown must be used. Given dimensions provide minimum clearance. Contact surface must be solid and level. RANGE OVERALL DIMENSIONS RANGEELECTRICAL CONNECTIONS FRONT......T...Y..P..I.C...A. LCABINETINSTALLATION SIDE VIEW 25-3/4" _1---- 30" 30" Minimum 1÷13"-* 8 "\ Wall Door Open \\,4_.29-7/8" .'_.> \ _t _ / - - t _ . Edge 2-5/8"for models equipped ._J-J- / Fig. 1 ** Depth is 28-13/32"with door handle, withwarmer drawers. 3w-i1th/2s"tfoorramgeoddrealws eeqrsuipped Fig. 2 wall on either side of range Minimumto 1" -_" ®_ ÷ _| _'_ above 36" height. 18" cabinetson ®® either side / Minimumto _1, of range, Maximumdepth for cabinets _ above rangetop. ........... Fig. 3 _'_ 30" _ 0" clearancebelow cookingtop and at rearof range. *30" MINIMUMCLEARANCE BETWEENTHE TOP OFTHE COOKINGSURFACEAND THE BOTTOMOFAN UNPROTECTEDWOOD OR METAL CABINET; OR24" MINIMUMWHEN BOTTOMOF WOOD OR METAL CABINET IS PROTECTEDBY NOT LESS THAN 1/4" FLAME RETARDANT MILLBOARDCOVEREDWITH NOT LESS THAN NO.28 MSG SHEET STEEL,0.015" STAINLESSSTEEL,0.024"ALUMIN UM OR0.020"COPPER. 0" CLEARANCE IS THE MINIMUM FOR THE REAR OF THE RANGE. FOLLOW ALL DIMENSION REQUIREMENTS PROVIDED ABOVE TO PREVENT PROPERTY DAMAGE, POTENTIAL FIRE HAZARD, AND INCORRECT COUNTERTOP AND CABINET CUTS. TO ELIMINATE THE RISK OF BURNS OR FIRE BY REACHING OVER HEATED SURFACE UNITS, CABINET STORAGE SPACE LOCATED ABOVE THE SURFACE UNITS SHOULD BE AVOIDED. IF CABINET STORAGE IS TO BE PROVIDED, THE RISK CAN BE REDUCED BY INSTALLING A RANGE HOOD THAT PROJECTS HORIZONTALLY A MINIMUM OF 5" BEYOND THE BOTTOM OF THE CABINETS. IMPORTANT SAFETY INSTRUCTIONS Important Note to the Consumer Keep these instructions with your owner's guide for future reference. • ALL RANGES CAN TIP • INJURYTO PERSONS COULD RESULT • INSTALL ANTI-TIP DEVICE PACKED WITH RANGE • SEE INSTALLATION INSTRUCTIONS If the information in this manual is not followed exactly, a fire or electrical shock may result causing property damage, personal injury or death. Important Notes to the Installer • Read all instructions contained in these installation instructions before installing range. • Remove all packing material from the oven compartments before connecting the gas & electrical supply to the range. • Observe all governing codes and ordinances. • Be sure to leave these instructions with the consumer. EspaSol - Paginas 5-8 • As when using any appliance generating heat, there are certain safety precautions you should follow. These are listed in the Use & Care Guide, read it carefully. • Be sure your range is installed and grounded properly by a qualified installer or service technician. • Make sure the wall coverings around the range can withstand the heat generated by the range. • To eliminate the need to reach over the surface elements, cabinet storage space above the elements should be avoided. Serial Plate Locations: Serial Serial plate is located on the lower right front frame of the appliance. Alternate location may be under cooktop. pin 316454912 rev A