Kenwood DVF-3060 User Manual - Page 46

46 In case of difficulty DV-603/DVF-3060/DVF-3060K (EN/K,P,E,T,M,X,Y) What appears to be a malfunction may not always be serious. If your unit should not perform as expected, consult the table below to see if the problem can be corrected before seeking help from your dealer or service representative. Operation to reset The microprocessor may fall into malfunction (impossibility to operate erroneous display, etc.) when the power cord is unplugged while power is ON or due to an external factor. In this case, execute the following procedure to reset the microprocessor and return it to normal condition. ÷ Please note that resetting the microprocessor clears the contents stored in, it returns the microprocessor to the condition when it left the factory. 1 In Power ON condition, keep the 7 (Stop) key and the ¡ (Search) key pressed at the same time. 2 When both keys are pressed, the region code of the unit, the software version, etc. will be displayed on the display. (When nothing is done, the display of this information continues.) Example: 72. 14.02:05 3 Press the POWER ON/OFF switch to go to Power OFF. 4 When Power ON is performed with the POWER ON/OFF switch, the settings become the default factory settings. DVD player unit Symptom Cause Remedy Playback does not start when the 6 key is pressed. ÷ There is no disc in the player. ÷ There are no signals recorded on the side of the disc being played. ÷ Load a disc and press the 6 key. ÷ Turn the disc over and properly place it on the disc tray. Playback starts but no image/sound is seen/ heard. ÷ The TV is not turned on. ÷ The connection cords are not properly con- nected. ÷ Turn on the TV. ÷ Properly reconnect the connection cords. The picture is disrupted when the image is ÷ The picture is slightly disrupted during fast ÷ This is not a malfunction. fast forwarded or fast reversed. forward and fast reverse operations. No sound is heard. ÷ The audio output cords are not properly connected. ÷ The volume control of the TV or amplifier is not adjusted properly. ÷ The player is in a special playback mode. ÷ Properly connect the audio cords. ÷ Set the sound volume to an appropriate level. ÷ Press the 6 key to resume normal playback mode. The picture does not look good or the pic- ÷ A nearby device is generating noise. ture/sound quality is poor. ÷ The disc is dirty. ÷ The disc is damaged. ÷ There is condensation on the optical lens. ÷ Separate this unit as far as possible from the device you think is generating the noise. ÷ Refer to the "Disc handling precautions" section and wipe dirt from the disc. 0 ÷ Use a new disc. ÷ Refer to the "Caution on condensation" sec- tion and evaporate the condensation. 0 It takes a while for the disc to start playing. ÷ Time is required for the unit to detect the disc type and size and for the rotation of the motor to stabilize. This is not a malfunction. ÷ Approximately 10 to 20 seconds are required for a disc to start playing, although the time differs depending on the disc. The tray opens automatically. ÷ The disc is not placed horizontally. ÷ Properly place the disc on the tray. The top and bottom of the screen cannot be seen. ÷ The video format of the disc being played does not match that of the connected TV monitor. ÷ Refer to the "Video formats" section ,and use a disc with the appropriate video for- mat for your TV or a TV with the appropriate video format for the disc. 9 The subtitle is not displayed. ÷ The DVD disc being played does not contain the recording of subtitles. ÷ The subtitle mode is set to off. ÷ The subtitle cannot be displayed when the DVD disc being played does not contain the recording of subtitles. ÷ Press the SUBTITLE ON/OFF key to switch on the subtitle mode. ¡ The voice (or subtitle) language cannot be changed. ÷ The DVD disc being played does not contain the recording of more than one audio (or subtitle) language. ÷ The voice (or subtitle) language cannot be changed when the DVD disc being played does not contain the recording of more than one voice (or subtitle) language. The viewing angle cannot be changed. ÷ The DVD disc being played does not contain the recording of more than one angle. ÷ You are attempting to switch the angle in a DVD section where more than one angle is not recorded. ÷ The viewing angle cannot be changed when the DVD disc being played does not contain the recording of more than one angle. ÷ More than one viewing angle may be recorded only in limited sections in a disc. Knowledge