Kenwood KDC-MP435U Instruction Manual - Page 33

Troubleshooting Guide - wires

Get Kenwood KDC-MP435U PDF manuals and user guides View all Kenwood KDC-MP435U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Troubleshooting Guide Some functions of this unit may be disabled by some settings made on this unit. ! Cannot switch to Aux source. ▲ • AUX is not turned on. ☞ (page 25) • AUX cannot be used when the KCA-iP200 is connected. ! • Cannot set up the subwoofer. • Cannot set up subwoofer phase. • No output from the subwoofer. • Cannot set up the low pass filter. ▲ • (page 9) is not set to On. • The Dual zone function is enabled. ☞ (page 9) ! • Cannot set up the high pass filter. • Cannot set up the Fader. ▲ The Dual zone function is enabled. ☞ (page 9) ! Cannot set up the subwoofer phase. ▲ Low pass filter is set to Through. ☞ (page 9) ! • Cannot select the output destination of the subsource in the Dual zone. • Cannot adjust the volume of the rear speakers. ▲ The Dual zone function is disabled. ☞ (page 9) ! No Audio control effect on AUX. ▲ The Dual zone function is enabled. ☞ (page 9) ! Cannot register a security code. ▲ (page 26) is not turned off. ! Cannot play audio files. ▲ (page 26) is set to "2". ! Cannot File select. ▲ The Scan play or Random play function is enabled. What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. General ? The Touch Sensor Tone doesn't sound. ✔ The preout jack is being used. ☞ The Touch Sensor Tone can't be output from the preout jack. Tuner source ? Radio reception is poor. ✔ The car antenna is not extended. ☞ Pull the antenna out all the way. ✔ The antenna control wire is not connected. ☞ Connect the wire correctly, referring to the section on (page 30). Disc source ? The specified disc does not play, but another one plays instead. ✔ The specified CD is quite dirty. ☞ Clean the CD. ✔ The disc is loaded in a different slot from that specified. ☞ Eject the disc magazine and check the number for the specified disc. ✔ The disc is severely scratched. ☞ Try another disc instead. Audio file source ? The sound skips when an Audio file is being played. ✔ The media is scratched or dirty. ☞ Clean the media, referring to the CD cleaning of the section on (page 6). ✔ The audio file is broken or not supported. ☞ Damaged and unsupported files are skipped. ✔ The recording condition is bad. ☞ Record the media again or use another media. English | 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Some functions of this unit may be disabled by
some settings made on this unit.
!
Cannot switch to Aux source.
▲
•
AUX is not turned on.
☞
<Built-in Auxiliary input
Setting> (page 25)
•
AUX cannot be used when the KCA-iP200 is
connected.
!
•
Cannot set up the subwoofer.
•
Cannot set up subwoofer phase.
•
No output from the subwoofer.
•
Cannot set up the low pass filter.
▲
•
<Subwoofer Output> (page 9) is not set to On.
•
The Dual zone function is enabled.
☞
<Audio
Setup> (page 9)
!
•
Cannot set up the high pass filter.
•
Cannot set up the Fader.
▲
The Dual zone function is enabled.
☞
<Audio
Setup> (page 9)
!
Cannot set up the subwoofer phase.
▲
Low pass filter is set to Through.
☞
<Audio Setup>
(page 9)
!
•
Cannot select the output destination of the
subsource in the Dual zone.
•
Cannot adjust the volume of the rear speakers.
▲
The Dual zone function is disabled.
☞
<Audio
Setup> (page 9)
!
No Audio control effect on AUX.
▲
The Dual zone function is enabled.
☞
<Audio
Setup> (page 9)
!
Cannot register a security code.
▲
<Demonstration mode Setting> (page 26) is not
turned off.
!
Cannot play audio files.
▲
<CD Read Setting> (page 26) is set to "2".
!
Cannot File select.
▲
The Scan play or Random play function is enabled.
What might seem to be a malfunction in your unit
may just be the result of slight misoperation or
miswiring. Before calling service, first check the
following table for possible problems.
General
?
The Touch Sensor Tone doesn’t sound.
✔
The preout jack is being used.
☞
The Touch Sensor Tone can’t be output from the
preout jack.
Tuner source
?
Radio reception is poor.
✔
The car antenna is not extended.
☞
Pull the antenna out all the way.
✔
The antenna control wire is not connected.
☞
Connect the wire correctly, referring to the
section on <Connecting Wires to Terminals>
(page 30).
Disc source
?
The specified disc does not play, but another one
plays instead.
✔
The specified CD is quite dirty.
☞
Clean the CD.
✔
The disc is loaded in a different slot from that
specified.
☞
Eject the disc magazine and check the number
for the specified disc.
✔
The disc is severely scratched.
☞
Try another disc instead.
Audio file source
?
The sound skips when an Audio file is being
played.
✔
The media is scratched or dirty.
☞
Clean the media, referring to the CD cleaning of
the section on <Handling CDs> (page 6).
✔
The audio file is broken or not supported.
☞
Damaged and unsupported files are skipped.
✔
The recording condition is bad.
☞
Record the media again or use another media.
English
|
33
Troubleshooting Guide