Kenwood VR-6060 User Manual - Page 22

Preparing for surround sound 4 Repeat steps 3 to input the distance for each of the speakers. 5 Press the SETUP key again to return to main setup displays. • The speakers you have selected should appear on the display. Confirm that all the speakers have been correctly selected. 6 Select the display mode. 1 Press the M/? key or Joystick (2/3) to select the DISP MODE. 2 Press the SETUP key for the following displays: 1 DISP SELECTOR : Displays the current input selector. 2 DISP LISTEN : Displays the current listen mode. 3 Use the MULTI CONTROL knob or Joystick (5/∞) to select the display mode. SP MUTE OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ. DTS. DOLBY DIGITAL STEREO NEO:6 THX L ACTIVE EQ. MATRIX C SW R A B CLIP COAXIAL ANALOG 96kHzfs DSP MODE DISCRETE PRO LOGIC LOUDNESS CSII Surround EX LFE SL S SB SR RDS RTY AUTO MEMO STEREO TUNED 4 Press the SETUP key again to accept the setting. 5 Use the M key or Joystick (3) to select EXIT. SP MUTE OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ. DTS. DOLBY DIGITAL STEREO NEO:6 THX L ACTIVE EQ. MATRIX C SW R A B CLIP COAXIAL ANALOG 96kHzfs DSP MODE DISCRETE PRO LOGIC LOUDNESS CSII Surround EX LFE SL S SB SR RDS RTY AUTO MEMO STEREO TUNED 6 Press the SETUP key to exit the SET UP mode. Input level adjustment (analog sources only) If the input level of an analog source signal is too high, the CLIP indicator will blink to indicate the source signal. Adjust the input level. SP MUTE OPTICAL 6CH INPUT AUTO DETECT CINEM ACTIV L C SW R A B CLIP COAXIAL ANALOG 96kHzfs DSP M LFE SL S SB SR 1 Use the Input Selector keys to select the source of which the input level you want to adjust. • You can store a separate input level for each input source. 2 Press the SOUND and M/? keys or Joystick (2/3) repeatedly until the "INPUT" indication appears. 3 Use the MULTI CONTROL knob or Joystick (5/∞) to adjust the input level. SP MUTE OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ. DTS. DOLBY DIGITAL STEREO NEO:6 THX L ACTIVE EQ. MATRIX C SW R A B CLIP COAXIAL ANALOG 96kHzfs DSP MODE DISCRETE PRO LOGIC LOUDNESS CSII Surround EX LFE SL S SB SR RDS RTY AUTO MEMO STEREO TUNED • The adjustment mode is displayed for approximately 8 seconds. • The input level may be adjusted to any one of three settings: 0dB, -3dB, and -6dB. (The initial setting is 0dB.) 4 Press the SOUND key again to return to the input indication. Normal playback Preparing for playback Some preparatory steps are needed before starting playback. POWER ON/STANDBY (VR-6060) A SPEAKERS B ON/STANDBY (KRF-V8060D) INPUT MODE POWER ON/OFF MD/TAPE (KRF-V8060D) Turning on the receiver 1 Turn on the power to the related components. 2 Turn on the power to this receiver by pressing the POWER ON/STANDBY key (for VR-6060) or POWER ON/OFF and ON/STANDBY (for KRF-V8060D) key. Selecting the input mode If you have selected a component connected to the CD/DVD, VIDEO 2, VIDEO 3 or DVD/6CH jacks, make sure that the input mode setting is correct for the type of audio signal to be used. 8 Selecting MD/TAPE Select the source name corresponding to the component connected to the MD/TAPE jacks. The initial factory setting is "TAPE". To change the source to "MD", follow the steps below: Hold down the MD/TAPE key for more than 2 seconds. • The source indication changes to "MD". • To return to the original indication, repeat the above procedure. Selecting the speaker system Press the A SPEAKERS B key to select the speaker system to be used. A ON : B ON : A+B ON : A+B OFF : Sound from the speakers connected to the SPEAKERS A terminals on the rear panel. Sound from the speakers connected to the SPEAKERS B terminals on the rear panel. No sound will be heard from the subwoofer. Sound from both the speakers connected to the SPEAKERS A and B terminals on the rear panel. No sound from the speakers. Use this setting when listening with headphones for stereo sound in all playback modes. The display segments are different depending on the type of input signal. The indicator for the speakers you want to use should be lit. SP MUTE OPTICAL 6CH INPUT AUTO DETECT CINEM ACTIV L C SW R A B CLIP COAXIAL ANALOG 96kHzfs DSP M LFE SL S SB SR • Selecting "6CH INPUT" by pressing the INPUT MODE key, whereby "DVD/6CH" is the input source will cause SPEAKERS A to be selected automatically. 22 EN