KitchenAid KFIS29PBMS Use & Care Guide - Page 34

Doors - chilled

Get KitchenAid KFIS29PBMS PDF manuals and user guides View all KitchenAid KFIS29PBMS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

TROUBLESHOOTING PROBLEM POSSIBLE CAUSES Water is leaking or dripping from the dispenser system NOTE: A few drops of water after dispensing is normal. The glass was not held under the dispenser long enough. Water continues to drip from The refrigerator has just been the dispenser beyond the installed. first few drops. The water filter was recently installed or replaced. Water is leaking from the back of the refrigerator Water from the dispenser is warm The water line connections were not fully tightened. Recently removed the doors and did not fully tighten water line connection Water from the dispenser is chilled to 50°F (10°C). The refrigerator has just been installed. A large amount of water was recently dispensed. Water has not been recently dispensed. The refrigerator is not connected to a cold water pipe. SOLUTIONS Hold the glass under the dispenser 2 to 3 seconds after releasing the dispenser lever. Flushing the water system removes the air from the lines which causes the water dispenser to drip. Flush the water system. See "Water and Ice Dispensers." Flushing the water system removes the air from the lines which causes the water dispenser to drip. Flush the water system. See "Water and Ice Dispensers." See "Connecting the Water." See "Refrigerator Doors and Drawer." This is normal. Allow 24 hours after installation for the water supply to cool completely. Allow 3 hours for the water supply to cool completely. The first glass of water may not be cool. Discard the first glass of water dispensed. Make sure the refrigerator is connected to a cold water pipe. See "Water Supply Requirements." Doors WARNING Explosion Hazard Use nonflammable cleaner. Failure to do so can result in death, explosion, or fire. To view an animation showing how to adjust and align the doors, refer to the Product Help/FAQ section of the brand website and search for "door closing and door alignment." PROBLEM POSSIBLE CAUSES SOLUTIONS The doors will not close completely The door is blocked open. A bin or shelf is in the way. Move food packages away from door. Push bin or shelf back into the correct position. Recently installed Remove all packaging materials. The doors are difficult to open The door gaskets are dirty or sticky. Clean gaskets and contact surfaces with mild soap and warm water. Rinse and dry with soft cloth. The doors appear to be uneven The doors need to be aligned, or the See "Door Closing and Door Alignment." refrigerator needs to be leveled. 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
34
TROUBLESHOOTING
Doors
To view an animation showing how to adjust and align the doors, refer to the Product Help/FAQ section of the brand website and search
for “door closing and door alignment.”
Water is leaking or dripping
from the dispenser system
NOTE:
A few drops of water
after dispensing is normal.
The glass was not held under the
dispenser long enough.
Hold the glass under the dispenser 2 to 3 seconds after
releasing the dispenser lever.
Water continues to drip from
the dispenser beyond the
first few drops.
The refrigerator has just been
installed.
Flushing the water system removes the air from the lines
which causes the water dispenser to drip. Flush the water
system. See “Water and Ice Dispensers.”
The water filter was recently installed
or replaced.
Flushing the water system removes the air from the lines
which causes the water dispenser to drip. Flush the water
system. See “Water and Ice Dispensers.”
Water is leaking from the
back of the refrigerator
The water line connections were not
fully tightened.
See “Connecting the Water.”
Recently removed the doors and did
not fully tighten water line connection
See “Refrigerator Doors and Drawer.”
Water from the dispenser is
warm
Water from the dispenser is chilled to
50°F (10°C).
This is normal.
The refrigerator has just been
installed.
Allow 24 hours after installation for the water supply to cool
completely.
A large amount of water was recently
dispensed.
Allow 3 hours for the water supply to cool completely.
Water has not been recently
dispensed.
The first glass of water may not be cool. Discard the first
glass of water dispensed.
The refrigerator is not connected to a
cold water pipe.
Make sure the refrigerator is connected to a cold water pipe.
See “Water Supply Requirements.”
PROBLEM
POSSIBLE CAUSES
SOLUTIONS
The doors will not close
completely
The door is blocked open.
Move food packages away from door.
A bin or shelf is in the way.
Push bin or shelf back into the correct position.
Recently installed
Remove all packaging materials.
The doors are difficult to
open
The door gaskets are dirty or sticky.
Clean gaskets and contact surfaces with mild soap and
warm water. Rinse and dry with soft cloth.
The doors appear to be
uneven
The doors need to be aligned, or the
refrigerator needs to be leveled.
See “Door Closing and Door Alignment.”
PROBLEM
POSSIBLE CAUSES
SOLUTIONS
WARNING
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.