Konica Minolta AccurioPress C3080 AccurioPress C2070/C3080 Series Daily Mainte - Page 138

AccurioPress C2070/C2070P/C2060/C3080/C3080P/C3070, AccurioPrint C2060L/C3070L

3-67

3.6

Details of quality adjustment items

3

24

Press [OK].

25

Press [Exit [ADJUSTMENT]].

Wait for the display [Now adjusting] to disappear.

26

Press [PrintMode] on the [Maximum Density Adj.] screen, and output the chart from the same tray in

step 5.

27

Measure all the maximum density patches of each color in the order of K, C, M, Y.

Repeat the adjustment from step 22 to step 27 until the maximum density is within the acceptable target

density range.

Acceptable target density range:

Y, M, C: from -5% to +5%, K: from -5% to +10%

3.6.10

[Max. Density Auto Adj.]

The Maximum Density Auto Adjustment is:

-

When

Intelligent Quality Optimizer IQ-501

is provided, the density is automatically adjusted using

In-

telligent Quality Optimizer IQ-501

.

-

When


is not provided, the density is adjusted using

Relay Unit

RU-509

/

Relay Unit RU-518

.

This section describes how to make adjustments using

Relay Unit RU-509

/

Relay Unit RU-518

without

In-

telligent Quality Optimizer IQ-501

.

Automatically adjust the maximum density for each of Y, M, C, and K colors by scanning printed charts with

the color sensor density mounted on

Relay Unit RU-509

/

Relay Unit RU-518

.

NOTICE

Be sure to use the paper for registering a desired density to perform Max. Density Auto Adj.. With an unreg-

istered paper, the adjustment cannot be performed correctly.

If you want to perform automatic adjustment using paper other than a registered paper, you need to register

a desired density again. For details, contact your service representative.

When this adjustment is conducted, proceed to the calibration with the Image controller.

Be sure to perform Color Density Manual Control after changing the maximum density.

Tips

-

After Max. Density Auto Adj., the paper profile used for automatic adjustment changes to the one used

for registering a desired density; the profile does not return to the one before adjustment. You can ask

a service engineer to specify the setting so that after this adjustment the paper profile automatically re-

turns to the one before adjustment. For details, contact your service representative.

-

When


is mounted, [Maximum Density Auto Adjustment] is dis-

played. When


is not mounted, [Max. Density Auto Adj. (RU)] is

displayed.

Section	Page
Table of contents	4
1 Daily Care	7
1.1 About Daily Care	7
Care Timing	7
Care requirements	7
1.2 Cleaning the Duplex Part	8
1.3 Cleaning Main Body Tray	11
1.4 Cleaning Multi Bypass Tray MB-506 or Multi Bypass Tray MB-508	13
1.5 Cleaning Paper Feed Unit PF-602m	14
1.6 Cleaning Paper Feed Unit PF-707 or Paper Feed Unit PF-707m	18
1.7 Cleaning Large Capacity Unit LU-202m, Large Capacity Unit LU-202XL, or Large Capacity Unit LU- 202XLm	20
2 Both Sides Adjust	23
2.1 What is Both Sides Adjust?	23
2.2 Adjustment flow to use paper of a new brand, weight, or size	24
2.2.1 Adjustment Timing	24
2.2.2 Adjustment Order	24
2.3 Regular adjustment flow	25
2.3.1 Adjustment Timing	25
2.3.2 Adjustment Order	25
2.3.3 Periodical Both Sides Adjustment Function	26
2.4 Adjustment flow for each job	27
2.4.1 Adjustment Timing	27
2.4.2 Adjustment Order	27
2.5 How to Operate the Both Sides Adj. Item	28
2.5.1 Finely adjust the side guide plates of the paper tray (for PF-707/PF-707m/PF- 602m)	28
2.5.2 [Front] Adjustment	31
2.5.3 [Gap] Adjustment (Back side adjustment)	36
2.5.4 [Scan Meas.] Adjustment	41
2.5.5 [Rotate/Skew] Adjustment	51
2.5.6 [AutoMeasure] Adjustment	58
2.5.7 Registering Paper Profile	62
2.5.8 Back Side Fine Adjustment	64
2.5.9 [Periodical Both Sides Adj.]	69
3 Quality Adj.	73
3.1 Quality Adjustment for Image Controller IC-603/ Image Controller IC-605	73
3.2 Regular adjustment flow (Standard)	74
3.2.1 Adjustment timing	74
3.2.2 Adjustment sequence	74
3.3 Regular adjustment flow (High accuracy)	75
3.3.1 Adjustment Timing	75
3.3.2 Adjustment Order	75
3.4 Adjustment flow to use a new type of paper	76
3.4.1 Adjustment timing	76
3.4.2 Adjustment sequence	76
3.5 Adjustment Flow when changing the screen	77
3.5.1 Adjustment timing	77
3.5.2 Adjustment sequence	77
3.6 Details of quality adjustment items	78
3.6.1 Setting of the Custom Screen	78
3.6.2 [Gamma Automatic Adjustment]	80
Performing [Gamma Automatic Adj.]	80
3.6.3 [Density Balance Adjustment] (for i1Pro, i1Pro2, or i1iSisXL)	82
Saving the measured data of the density balance	90
3.6.4 [Density Balance Adjustment] (for FD-5BT)	92
3.6.5 Registering the adjusted value of the density balance in the machine	103
3.6.6 [Density Balance Auto. Adj.]	110
3.6.7 [Maximum Density Adjustment]	120
3.6.8 [Maximum Density Adjustment] (for i1Pro/i1Pro2)	121
3.6.9 [Maximum Density Adjustment] (for FD-5BT)	130
3.6.10 [Max. Density Auto Adj.]	138
3.6.11 Checking the Color Density Control Setting	141
3.6.12 [Color Density Manual Control]	144
3.6.13 About Controller Calibration	147
Executing Calibration	148
3.6.14 About Exact Color calibration	154
Executing Exact Color: Color Centro	155
Executing Exact Color: Touch panel	162
3.6.15 About G7 Calibration	165
Executing G7 Calibration: Color Centro	166
Executing G7 Calibration: Touch panel	172

Konica Minolta AccurioPress C3080 AccurioPress C2070/C3080 Series Daily Mainte - Page 138

[Max. Density Auto Adj.], is not mounted, [Max. Density Auto Adj. RU] is

Page 138 highlights