Konica Minolta KIP 7170 KIP 7170 User Manual - Page 22

Treatment against environmental condition, Turn on the Dehumidify Heater.

Get Konica Minolta KIP 7170 PDF manuals and user guides View all Konica Minolta KIP 7170 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

1. 7. 3 Treatment against environmental condition Take a necessary treatment according to the environmental condition as shown below. Humidity(%) Low 40% 70% High Possible problem "Void of image", "crease of paper" and other problems occurs when you print with plain paper and tracing paper. "Void of image" occurs when you print with tracing paper. "Void of image" occurs when you print with plain paper and tracing paper. "Void of image", "crease of paper" and other problems occurs when you print with plain paper and tracing paper. Necessary treatment 1. Install the humidifier in the room, and humidify the room air. 2. Remove the paper from the machine right after the completion of print, and keep it in a polyethylene bag. If you will not make print soon, remove the tracing paper from the machine and keep it in a polyethylene bag. Remove the paper from the machine after everyday use, and keep it in a polyethylene bag. If you will not make print soon, remove the tracing paper from the machine and keep it in a polyethylene bag. 1. Turn on the Dehumidify Heater. (if installed) 2. Remove the paper from the machine right after the completion of print, and keep it in a polyethylene bag. NOTE (1) KIP 7170 is equipped with the Dehumidify Heater (optional for the US). Using it in high humidity environment (75% or higher) is recommended. Refer to [2.9 Dehumidifying Roll Paper]. (2) "Void of image" and "crease of paper" will occur in case of extremely high or low humidity. Normal Print Crease of paper If the media is humidified; Normal Print Loss of image If the media is humidified; 1-16 Chapter 1 Before Use

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Chapter 1
Before Use
1-16
1. 7. 3
Treatment against environmental condition
Take a necessary treatment according to the environmental condition as shown below.
Humidity(%)
Possible problem
Necessary treatment
Low
40%
70%
High
“Void of image”, “crease of paper” and
other problems occurs when you print
with plain paper and tracing paper.
1.
Install the humidifier in the room, and
humidify the room air.
2.
Remove the paper from the machine
right after the completion of print, and
keep it in a polyethylene bag.
“Void of image” occurs when you print
with tracing paper.
If you will not make print soon, remove
the tracing paper from the machine and
keep it in a polyethylene bag.
Remove the paper from the machine after
everyday use, and keep it in a
polyethylene bag.
“Void of image” occurs when you print
with plain paper and tracing paper.
If you will not make print soon, remove
the tracing paper from the machine and
keep it in a polyethylene bag.
“Void of image”, “crease of paper” and
other problems occurs when you print
with plain paper and tracing paper.
1.
Turn on the Dehumidify Heater.
(if installed)
2.
Remove the paper from the machine
right after the completion of print, and
keep it in a polyethylene bag.
NOTE
(1) KIP 7170 is equipped with the Dehumidify Heater (optional for the US).
Using it in high humidity environment (75% or higher) is recommended.
Refer to [2.9
Dehumidifying Roll Paper].
(2)
“Void of image” and “crease of paper” will occur in case of extremely high or low
humidity.
Normal Print
Normal Print
If the media is humidified;
If the media is humidified;
Crease of paper
Loss of image