Konica Minolta KIP 7170 KIP 7170 User Manual - Page 8

Installation Requirements - paper options

Get Konica Minolta KIP 7170 PDF manuals and user guides View all Konica Minolta KIP 7170 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

1. 1 Installation Requirements The following conditions are required for installation of the equipment. 1. POWER SOURCE should be rated as follows. In U.S.A. : 120V plus/minus 10%, 50/60Hz, 15A or higher In Europe : 220-240V plus 6% or minus10%, 50/60Hz, 10A or higher 2. The equipment must be on an exclusive circuit. 3. The outlet must be near the equipment and easily accessible. I Norge: Kan kobles til IT strøm distribusjonssystemer. 1. Make sure to connect this equipment to a grounded outlet. 2. For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the equipment and shall be easily accessible. The site temperature range = 10 to 32 degrees Centigrade, with the humidity between 15% to 85% RH. (NON CONDENSING) Keep the printer away from water sources, boilers, humidifiers, refrigerators or kerosene (oil) stove. 1. The installation site must not have open flames, dust or ammonia gases. 2. The equipment must not be exposed to the air vents from air conditioners. It may affect the image quality. 3. The equipment should not be exposed to the direct sunlight. Please draw curtains to block any sunlight. When you open the Movable Unit, do not expose the Photoconductive Drum to strong (intense) light as this will damage the Drum. Ozone will be generated while this equipment is use, although the quantity generated is within safe levels. (see certifications) Ventilate the room, if required. Keep ample room around the equipment to ensure comfortable operation. (Refer to the following figure.) The equipment must be leveled and the floor strength must be ample to sustain the weight of the equipment. (Rear) 30cm/12" or larger (w/o option) KIP 7170 L* R* (Front) 80cm/32" or larger 90cm/35.4" or larger for Paper Tray (option) * L + R = 35cm/14" or larger (R must be larger than L) (L = 5cm/2" or larger recommended) 1-2 Chapter 1 Before Use

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Chapter 1
Before Use
1-2
1. 1
Installation Requirements
The following conditions are required for installation of the equipment.
1.
POWER SOURCE
should be rated as follows.
In U.S.A.
: 120V plus/minus 10%, 50/60Hz, 15A or higher
In Europe : 220-240V plus 6% or minus10%, 50/60Hz, 10A or higher
2. The equipment must be on an exclusive circuit
.
3. The outlet must be near the equipment and easily accessible.
I Norge: Kan kobles til IT strøm distribusjonssystemer.
1. Make sure to connect this equipment to a grounded outlet.
2. For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near
the equipment and shall be easily accessible.
The site temperature range = 10 to 32 degrees Centigrade, with the humidity between
15% to 85% RH. (NON CONDENSING)
Keep the printer away from water sources, boilers, humidifiers, refrigerators or kerosene
(oil) stove.
1. The installation site must not have open flames, dust or ammonia gases.
2. The equipment must not be exposed to the air vents from air conditioners.
It may affect the image quality.
3. The equipment should not be exposed to the direct sunlight.
Please draw curtains to block any sunlight.
When you open the Movable Unit, do not expose the Photoconductive Drum
to strong (intense) light as this will damage the Drum.
Ozone will be generated while this equipment is use, although the quantity generated
is within safe levels. (see certifications)
Ventilate the room, if required.
Keep ample room around the equipment to ensure comfortable operation.
(Refer to the following figure.)
The equipment must be leveled and the floor strength must be ample to sustain the
weight of the equipment.
* L + R = 35cm/14” or larger
(R must be larger than L)
(L = 5cm/2” or larger
recommended)
KIP 7170
R*
30cm/12” or larger
(w/o option)
(Rear)
L*
(Front)
80cm/32” or larger
90cm/35.4” or larger
for Paper Tray (option)