Konica Minolta Kodak i620 User Guide - Page 15

Using the Scanner, Turning the scanner on and off, Starting and stopping scanning, on and off

Get Konica Minolta Kodak i620 PDF manuals and user guides View all Konica Minolta Kodak i620 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

3 Using the Scanner This chapter provides the following operational procedures: • Turning on/off the scanner • Starting, stopping, pausing and resuming the scanner • Document preparation • Adjusting the side guides and output tray • Scanning documents • Feeding long documents • Automatic, continuous and manual feeding • Calibration Turning the scanner on and off • Press the button on the scanner's lower right-side (I) to power it up. • Press the button on the scanner's lower right-side (O) to power it down. After you power up the scanner, wait until for it to complete self-test. When completed, the top green indicator light will remain on and constant. If this does not occur, refer to Chapter 6, "Indicator lights" for more information. IMPORTANT: Always power up the scanner to its ready state before powering up or restarting the host computer. Starting and stopping scanning Scanning is controlled by integration software developed for your application. To start and stop scanning, refer to the documentation provided with your integration software. If your application does not automatically start the scanner transport, begin the scanning process by pressing the Start/Resume button on the scanner. NOTE: Before you start scanning, make sure the scanner is ready for operation, which is indicated by the top green indicator light being on and constant. A-61500 April 2007 3-1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
A-61500
April 2007
3-1
3
Using the Scanner
This chapter provides the following operational procedures:
•
Turning on/off the scanner
•
Starting, stopping, pausing and resuming the scanner
•
Document preparation
•
Adjusting the side guides and output tray
•
Scanning documents
•
Feeding long documents
•
Automatic, continuous and manual feeding
• Calibration
Turning the scanner
on and off
•
Press the button on the scanner’s lower right-side (I) to power it up.
•
Press the button on the scanner’s lower right-side (O) to power it
down.
After you power up the scanner, wait until for it to complete self-test.
When completed, the top green indicator light will remain on and
constant. If this does not occur, refer to Chapter 6, “Indicator lights” for
more information.
IMPORTANT: Always power up the scanner to its ready state before
powering up or restarting the host computer.
Starting and stopping
scanning
Scanning is controlled by integration software developed for your
application. To start and stop scanning, refer to the documentation
provided with your integration software.
If your application does not automatically start the scanner transport,
begin the scanning process by pressing the
Start/Resume
button on
the scanner.
NOTE: Before you start scanning, make sure the scanner is ready for
operation, which is indicated by the top green indicator light
being on and constant.