Kyocera FS-C5300DN FS-C5100DN/C5200DN/C5300DN Operation Guide Rev-1.2 (BASIC) - Page 60

Black or white vertical streaks, MENU], Faint or blurred printing - drum

Get Kyocera FS-C5300DN - FS-C5300DN PDF manuals and user guides
UPC - 632983010303
View all Kyocera FS-C5300DN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Printed Results Black or white vertical streaks Direction of Paper Feed Faint or blurred printing Corrective Action Check the operation panel for toner. If the Toner low C,M,Y,K message is displayed with color description, install a new toner kit for the color. To replace the toner container, refer to Toner Container Replacement on page 3-2. Clean the main charger units. For details, refer to LSU/Charger (LSU/Main charger cleaning mode setting) section of the Advanced Operation Guide. Refresh drum. Perform the following procedures on the operation panel and try cleaning the drum surface using the printer's built-in cleaning system. 1 Press [MENU]. 2 Press U or V repeatedly until Adjust/Maintenance > appears. 3 Press Z. Press U or V repeatedly until >Service > appears. 4 Press Z. Press U or V repeatedly until >>Drum appears. 5 Press [OK] twice. 6 The message display shows Please wait. After approx. 3 minutes, the display returns to Ready. Clean the main charger units. For details, refer to LSU/Charger (LSU/Main charger cleaning mode setting) section of the Advanced Operation Guide. Make sure the paper type setting is correct the paper being used. For details, refer to Paper Settings section of the Advanced Operation Guide. Conduct color calibration either by switching the printer off then on or using the printer operation panel. For details, refer to Color Calibration section of the Advanced Operation Guide. Try adjusting the color control settings using the printer driver. Check the operation panel. If the Toner low C,M,Y,K message is displayed with color description, install a new toner kit for the color. To replace toner, refer to Toner Container Replacement on page 3-2. Refresh drum. Perform the following procedures on the operation panel and try cleaning the drum surface using the printer's built-in cleaning system. 1 Press [MENU]. 2 Press U or V repeatedly until Adjust/Maintenance > appears. 3 Press Z. Press U or V repeatedly until >Service > appears. 4 Press Z. Press U or V repeatedly until >>Drum appears. 5 Press [OK] twice. 6 The message display shows Please wait. After approx. 3 minutes, the display returns to Ready. 4-4 Troubleshooting

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
4-4
Troubleshooting
Black or white vertical streaks
Check the operation panel for toner.
If the
Toner low C,M,Y,K
message is displayed with color description,
install a new toner kit for the color. To replace the toner container, refer to
Toner Container Replacement on page 3-2.
Clean the main charger units.
For details, refer to
LSU/Charger
(LSU/Main charger cleaning mode
setting)
section of the
Advanced Operation Guide
.
Refresh drum.
Perform the following procedures on the operation panel and try cleaning
the drum surface using the printer's built-in cleaning system.
1
Press
[MENU]
.
2
Press
U
or
V
repeatedly until
Adjust/Maintenance
>
appears.
3
Press
Z
. Press
U
or
V
repeatedly until
>Service >
appears.
4
Press
Z
. Press
U
or
V
repeatedly until
>>Drum
appears.
5
Press
[OK]
twice.
6
The message display shows
Please wait
. After approx. 3 minutes,
the display returns to
Ready
.
Faint or blurred printing
Clean the main charger units.
For details, refer to
LSU/Charger
(LSU/Main charger cleaning mode
setting)
section of the
Advanced Operation Guide
.
Make sure the paper type setting is correct the paper being used.
For details, refer to
Paper Settings
section of the
Advanced Operation
Guide
.
Conduct color calibration either by switching the printer off then on or using
the printer operation panel.
For details, refer to
Color Calibration
section of the
Advanced Operation
Guide
.
Try adjusting the color control settings using the printer driver.
Check the operation panel. If the
Toner low C,M,Y,K
message is
displayed with color description, install a new toner kit for the color. To
replace toner, refer to
Toner Container Replacement on page 3-2.
Refresh drum.
Perform the following procedures on the operation panel and try cleaning
the drum surface using the printer's built-in cleaning system.
1
Press
[MENU]
.
2
Press
U
or
V
repeatedly until
Adjust/Maintenance
>
appears.
3
Press
Z
. Press
U
or
V
repeatedly until
>Service >
appears.
4
Press
Z
. Press
U
or
V
repeatedly until
>>Drum
appears.
5
Press
[OK]
twice.
6
The message display shows
Please wait
. After approx. 3 minutes,
the display returns to
Ready
.
Printed Results
Corrective Action
Direction
of Paper
Feed