Kyocera QCP-2760 User Manual - Page 64

Turn on your computer. - software

Get Kyocera QCP-2760 - Qualcomm Cell Phone PDF manuals and user guides View all Kyocera QCP-2760 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Check with your service provider to see if both voice and data/fax signals are supported. If the network cannot distinguish between voice and data/ fax calls, and you are expecting a data call, you can set the phone to data mode. Important-When the phone is in data mode, you cannot receive incoming voice calls. Setting up a data connection Follow these steps to set up a CDMA data connection. 1. With your phone turned off, plug the flat connector on one end of the data cable into the port on the bottom of the phone. 2. Plug the serial connector on the other end of the data cable into the serial port on your computer. 3. Turn on your computer. 4. Press pwr or to turn on the phone. 5. Open a communications software package on your computer. 6. To send or receive faxes and email or to access the Internet, follow the directions that came with the communications software. 54 Sending or Receiving Data

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
54
Sending or Receiving Data
Check with your service provider to see if both voice and data/fax signals
are supported. If the network cannot distinguish between voice and data/
fax calls, and you are expecting a data call, you can set the phone to data
mode.
Important—
When the phone is in data mode, you cannot receive incoming
voice calls.
Setting up a data connection
Follow these steps to set up a CDMA data connection.
1.
With your phone turned off, plug the flat connector on one end of the
data cable into the port on the bottom of the phone.
2.
Plug the serial connector on the other end of the data cable into the serial
port on your computer.
3.
Turn on your computer.
4.
Press
or
to turn on the phone.
5.
Open a communications software package on your computer.
6.
To send or receive faxes and email or to access the Internet, follow the
directions that came with the communications software.
pwr