Kyocera TASKalfa 180 Operation Guide - Page 25

Message Display, System Menu the mode after warm-up processing has been completed or Reset key - error codes

Get Kyocera TASKalfa 180 PDF manuals and user guides View all Kyocera TASKalfa 180 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Names of Parts Message Display The message display on the operation panel shows: • Status information, the messages listed below which are displayed during normal operation. • Error codes, when the printer requires the operator's attention, refer to chapter „Troubleshooting". Status Information Message Self test Please wait. Ready to copy. Meaning The copier is performing self-diagnostics after power-up. The copier is warming up and is not ready. When the copier is switched on for the first time, this message will take approximately 20 seconds. The copier is ready to copy. Error codes Refer to chapter „Troubleshooting". System Menu (the mode after warm-up processing has been completed or Reset key was pressed) The copier has been set at the factory to automatically select a magnification ratio of 1:1 for the same size of paper as the original in the Auto Mode with the No. of Copies at "1" and for the Image Quality. NOTE: The Default Settings can be changed in the System Menu. In the case where an optional cassette is present, the cassette selected in the System Menu can be changed. (Refer to appendix.) The Image Quality Mode selected in the System Menu can be changed. (Refer to appendix.) The Default Setting for the copy density can be changed to the Auto. (Refer to appendix.) Auto Clear function After the copy has been produced and a fixed interval (10 to 270 seconds) has elapsed, the copier will automatically revert to the state it was in when warm-up processing was completed.(However, the copy density mode and the Image Quality will not revert back to their original state. Copies can still be repeatedly produced with the same Copy Mode, No. of Copies, copy density and other settings if the Auto clear function has not been activated. NOTE: Please refer to appendix. Please refer to appendix for information on changing the time interval before the Auto clear function activates. Custom Sizes Paper and original sizes that are not displayed on the Operation Panel can be registered as Custom Sizes. (Inputting Custom Size on page 2-9.) 1-6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
Names of Parts
1-6
Message Display
The message display on the operation panel shows:
•
Status information, the messages listed below which are displayed during normal operation.
•
Error codes, when the printer requires the operator’s attention, refer to chapter „Troubleshooting“.
Status Information
Error codes
Refer to
chapter „Troubleshooting“.
System Menu (the mode after warm-up processing has been completed or Reset key
was pressed)
The copier has been set at the factory to automatically select a magnification ratio of 1:1 for the same size of
paper as the original in the Auto Mode with the No. of Copies at “1” and
for the Image Quality.
NOTE: The Default Settings can be changed in the System Menu.
In the case where an optional cassette is present, the cassette selected in the System Menu can be changed.
(Refer to appendix.)
The Image Quality Mode selected in the System Menu can be changed. (Refer to appendix.)
The Default Setting for the copy density can be changed to the
Auto
. (Refer to appendix.)
Auto Clear function
After the copy has been produced and a fixed interval (10 to 270 seconds) has elapsed, the copier will
automatically revert to the state it was in when warm-up processing was completed.(However, the copy density
mode and the Image Quality will not revert back to their original state. Copies can still be repeatedly produced
with the same Copy Mode, No. of Copies, copy density and other settings if the Auto clear function has not been
activated.
NOTE: Please refer to appendix. Please refer to appendix for information on changing the time interval before
the Auto clear function activates.
Custom Sizes
Paper and original sizes that are not displayed on the Operation Panel can be registered as Custom Sizes.
(Inputting Custom Size on page 2-9.)
Message
Meaning
Self test
The copier is performing self-diagnostics after power-up.
Please wait.
The copier is warming up and is not ready.
When the copier is switched on for the first time, this message will take
approximately 20 seconds.
Ready to copy.
The copier is ready to copy.