Kyocera TASKalfa 180 Operation Guide - Page 81

Logout, Energy saver, Display, Corrective Procedure, Reseat originals, on DP., Return all

Get Kyocera TASKalfa 180 PDF manuals and user guides View all Kyocera TASKalfa 180 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 81 highlights

Troubleshooting Display Reseat originals on DP. Return all originals to DP. Set paper cassette. Corrective Procedure Originals were set in the optional Document Processor when copying on 2-sides (front and back sides), when copying from the platen in 2-Sided copy, 2 in 1, 4 in 1 or when collating copies. Remove the originals from the Document Processor, replace the originals on the Original Table after exiting the front and back copying, 2-Sided copy, 2 in 1, 4 in 1 or Collate Mode and resume copying. If the optional Document Processor is being used, there are originals left on the original table. Remove the originals, return them to the original table and try copying them again. Check the paper cassette that corresponds to the lighting indicator. Set the cassette. Shake the toner container. Tap and shake the new toner container without spilling the toner, and install it again. Set toner container. The Toner Container has not been set. Set the Toner Container. The Add Toner indicator blinks on and off. The Periodic Maintenance indicator blinks on and off. The Periodic Maintenance indicator lights up. "= = =" appears on the copy quantity display. "-" appears on the copy quantity display. "---" appears on the copy quantity display. There is very little toner remaining. Copying can be continued for a short while before running out of toner. Prepare the toner container. This is a notification that the time for periodic maintenance is approaching. It is time for Periodic Maintenance. Contact your service representative. Job Accounting being set. Use the numeric keys to enter the assigned Section Code to perform copying operations. Press the Logout key after copying is finished to display "= = =" again. The copier is in the Sleep Mode setting. Press the Energy saver key to exit the mode. The copier is in the Low Power mode setting. Press any key to exit the mode or in the case where the optional Document Processor is installed, set an original in the Document Processor. 7-6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
Troubleshooting
7-6
Originals were set in the optional Document Processor
when copying on 2-sides (front and back sides), when
copying from the platen in 2-Sided copy, 2 in 1, 4 in 1 or
when collating copies. Remove the originals from the
Document Processor, replace the originals on the
Original Table after exiting the front and back copying,
2-Sided copy, 2 in 1, 4 in 1 or Collate Mode and resume
copying.
If the optional Document Processor is being used, there
are originals left on the original table. Remove the
originals, return them to the original table and try
copying them again.
Check the paper cassette that corresponds to the
lighting indicator. Set the cassette.
Tap and shake the new toner container without spilling
the toner, and install it again.
The Toner Container has not been set. Set the Toner
Container.
The Add Toner indicator blinks on
and off.
There is very little toner remaining. Copying can be
continued for a short while before running out of toner.
Prepare the toner container.
The Periodic Maintenance
indicator blinks on and off.
This is a notification that the time for periodic
maintenance is approaching.
The Periodic Maintenance
indicator lights up.
It is time for Periodic Maintenance. Contact your service
representative.
“= = =” appears on the copy
quantity display.
Job Accounting being set. Use the numeric keys to enter
the assigned Section Code to perform copying
operations. Press the
Logout
key after copying is
finished to display “= = =” again.
“-” appears on the copy quantity
display.
The copier is in the Sleep Mode setting. Press the
Energy saver
key to exit the mode.
“---” appears on the copy quantity
display.
The copier is in the Low Power mode setting. Press any
key to exit the mode or in the case where the optional
Document Processor is installed, set an original in the
Document Processor.
Display
Corrective Procedure
Reseat originals
on DP.
Return all
originals to DP.
Set paper
cassette.
Shake the toner
container.
Set toner
container.