LG 26LH1DC5 Owner's Manual - Page 65

PEFERENCE Detailed Information For Making A Master TV IMPORTANT INSTALLER SETUP INFORMATION! PLEASE READ THE FOLLOWING... To set up a master TV you will need to know how to enter the 26LH1DC3/4/5 Installer menu and make changes to the default values as required. If necessary, familiarize yourself with the 26LH1DC3/4/5 Installer menu and how to make and save changes in the menu, before attempting to clone the 26LH1DC3/4/5 Master TV setup. You will also need an Installer remote control similar to the one shown in the front of this manual. Finally, the TV's clonable features need to be set up. This is a critical step. If the Master TV display panel's clonable features like adding channel icons or channel labels are not correctly added, then the cloned 26LH1DC3/4/5s TVs will all have problems. As the cloning procedure is being performed, specific steps need to be done at the indicated times to achieve the desired result. Be sure to do each task as indicated. If a procedure or step is left out or not performed completely, cloning may not work. At each step, pay attention to assure the TV screen shows the proper message when cloning. If the message indicated does not appear, there is a problem with that step and cloning may not be successful. Cloning is only possible when the signal source is an Analog channel, not a digital channel. COMMERCIAL MODE Making a Master TV Detailed Instructions Channels only. 5. Assign ICONs to the channels using the Channel Label Menu. The following describes the procedure for preparing a Note: You can add Channel ICONS typically network Master 26LH1DC3/4/5 for cloning and the procedure logos like ABC, NBC, PBS etc. in this step. Or, in Step 7, for adding Channel Icons and/or Labels. add Channel ICONS or labels for channels without Note 1: Disconnect all Aux inputs. Under certain Icons. conditions, Auto Program Scan is disabled if there is an 6. Transfer the TV setup: Enter the 26LH1DC3/4/5 Aux input active. installer menu. Note 2: Under certain conditions, changes to the input Press '2', '5', '5', 'MENU' to start the transfer of the mode of the RGB inputs will not take effect until the TV's setup to the 26LH1DC3/4/5. Once the power is cycled (TV is turned Off and On). To avoid transfer is complete, the system will exit the Installer confusion, disconnect all RGB inputs before entering the menu. Installer menu. Note: Only do 2-5-5 + MENU once. The TV setup 1. Enter the 26LH1DC3/4/5 installer menu. may be corrupted if 255 + Menu is done more than a. Reset the internal controller to factory default by one time. accessing installer menu item 117 FACT DEFAULT, set 7. Edit/Add Channel ICONs and Channel Labels as needed. it to 1 and press "ENTER". The value will change Enter Installer menu. With menu displayed, press 2- back to 0 after the TV's internal controller has been 5-4 + MENU. restored to factory default condition. See page 62 for detailed instructions: b. Within the Installer menu, set the Installer menu - Editing/Adding Channel ICON and Labels on items to the configuration required of your Master TV institution. - Changing a Channel's ICON on Master TV c. It is important to set the tuning band at this time, - Changing/Adding Channel Labels on Master TV see - Changing Source Labels on Master TV Installer menu item 03 BAND/AFC. 8. Verify Master TV setup and feature configuration: d. Set Installer menu item 28 - CH OVERIDE to 001 • Did you add Channel ICONS? to allow access to the Auto Program and Channel • Did you add Channel Labels? List/Channel Label features in the Channel Menu. • Did you add Aux Source Labels? Exit the Installer menu. • Did you adjust all TV menu options as required? 2. Access the Master TV menus and set the clonable The TV master setup is now ready to be cloned. options on the menus to the desired configuration. Go to the master TV cloning section or continue on Refer to the Clonable Menu Features Chart on the to page 52. see page 63. After verifying master setup, enter the 26LH1DC3/4/5 3. Run Auto Program. Installer menu and set Installer menu item 028 Ch 4. Enter the Channel List/Channel Label menu and edit Overide to 000. the channel line-up to include the Free-To-Guest 65