LG BX327 User Manual - Page 15

Focus and Position of the Screen Image, Selecting input mode

Get LG BX327 PDF manuals and user guides View all LG BX327 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Installing and Composition Focus and Position of the Screen Image When an image appears on the screen, check if it is in focus and fits well to the screen. Focus ring Zoom ring ꔈꔈ To adjust the focus of the image, rotate the focus ring which is the outer ring on the lens. ꔈꔈ To adjust the size of the image, rotate the zoom ring which is the inner ring on the lens. To raise or lower the image on the screen, extend or retract the foot at the bottom of the projector by pushing foot adjusting button as below. Foot adjusting button 1. While pressing the foot adjusting button, raise or lower the projector to place the screen image in the proper position. 2. Release the button to lock the foot in its new position. 3. Turn the foot at the back left or right to make a fine tune of the length of the projector. 4. After raising the front foot, do not press down on the projector. Selecting input mode 1. Press the INPUT button on the remote control. 2. Selecting an input signal with the INPUT button will only change the projector only to connected inputs. You can change it to any inputs with the ＜, ＞ button. Input Video Component1 Component2 RGB1 RGB2 HDMI • The component input is always active, and it does not support plug &play function. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Installing and Composition
15
When an image appears on the screen, check if it is in focus and fits well to the screen.
ꔈ
To adjust the focus of the image, rotate the focus ring which is the outer ring on the lens.
ꔈ
To adjust the size of the image, rotate the zoom ring which is the inner ring on the lens.
Focus and Position of the Screen Image
To raise or lower the image on the screen, extend or retract the foot at the bottom of the projector
by pushing foot adjusting button as below.
1.
While pressing the foot adjusting button, raise or lower the projector to place the screen image in the proper position.
2. Release the button to lock the foot in its new position.
3. Turn the foot at the back left or right to make a fine tune of the length of the projector.
4. After raising the front foot, do not press down on the projector.
Focus ring
Zoom ring
Foot adjusting button
Selecting input mode
1. Press the
INPUT
button on the remote control.
2. Selecting an input signal with the
INPUT
button will only change the projector only to connected inputs. You
can change it to any inputs with the
＜
,
＞
button.
•
The component input is always active, and it does not support plug &play function.
Input
Component1
Video
RGB2
HDMI
RGB1
Component2