LG BX327 User Manual - Page 31

SET ID, How to connect external control equipment, Communication Parameter Setup - projector lamp

Get LG BX327 PDF manuals and user guides View all LG BX327 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Function SET ID 1. Press the MENU button. Then, move to OPTION with the buttons and press the ◉OK button. 2. Press the ∧, ∨ buttons to move to Set ID and press the ◉OK button. 3. Press the ＜, ＞ button to select your desired number. Press the ◉OK button to save the selected number. • The adjustment range of Set ID is 1~99. • Only the projector with the specified ID number will operate from the remote control. • Press the BACK button to exit the menu screen. How to connect external control equipment * Connect the serial port of the PC to the RS-232C jack on the projector back panel. * RS-232C cable is not supplied with the projector. OPTION Menu Language Blank Image Screen Capture Lamp Mode Monitor Out Set ID Network Setting High Altitude 3D Mode : English : Blue : Normal : RGB1 : 1 : Off ꔂMove ꔉOK * Use the RS232C cable to control the projector externally (Refer to Fig.1). RXD 2 TXD 3 DTR 4 GND 5 DSR 6 RTS 7 CTS 8 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS PC Projector * 1, 9 Pin No Connection 96 5 1 Communication Parameter Setup • Baud Rate : 9600bps(UART) • Data Length : 8bit • Parity : none • Stop bit : 1bit • Flow Control : none • Communication code : ASCII code 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Function
31
1. Press the
MENU
button. Then, move to
OPTION
with the
∧
,
∨
,
＜
,
＞
buttons and press the
◉
OK
button.
2. Press the
∧
,
∨
buttons to move to
Set ID
and press the
◉
OK
button.
3. Press the
＜
,
＞
button to select your desired number. Press the
◉
OK
button to save the selected number.
•
The adjustment range of
Set ID
is 1~99.
•
Only the projector with the specified ID number will operate from the
remote control.
• Press the
BACK
button to exit the menu screen.
OPTION
Menu Language
: English
Blank Image
: Blue
Screen Capture
Lamp Mode
: Normal
Monitor Out
: RGB1
Set ID
: 1
Network Setting
High Altitude
: Off
3D Mode
ꔂ
Move
ꔉ
OK
SET ID
* Connect the serial port of the PC to the RS-232C jack on the projector back panel.
* RS-232C cable is not supplied with the projector.
* Use the RS232C cable to control the projector externally (Refer to Fig.1).
<Fig.1, RS-232 Interface Cable>
* 1, 9 Pin No Connection
2
3
4
5
6
7
8
RXD
TXD
DTR
GND
DSR
RTS
CTS
RXD
TXD
DTR
GND
DSR
RTS
CTS
2
3
4
5
6
7
8
PC
Projector
Communication Parameter Setup
•
Baud Rate : 9600bps(UART)
•
Data Length : 8bit
•
Parity : none
•
Stop bit : 1bit
•
Flow Control : none
•
Communication code : ASCII code
9
6
1
5
How to connect external control equipment