LG L26W58HA Operation Guide - Page 54

IMPORTANT INSTALLER SETUP INFORMATION! PLEASE READ THE FOLLOWING... enter the L26W58HA Installer menu and make changes to Tthoesedtefuapulta vmaalusetesr aTsVreyqouirewdiU. n[feendecteosskanroyw, fahmoiwliatroize yourself with the L26W58HA Installer menu and how to make and save changes in the menu, before attempting to clone the E26W58HA Master TV setup. You wiU also need an Installer remote control similar to the one shown in the front of this manual. FinaUy, the TV's donabte features need to be set up. This is a critical step. If the Master TV display panel's donabte features [ike adding channel icons or channel Labels are not correctly added, then the cloned L26W58HAs TVs will all have problems. As the cloning procedure isbeing performed, specific steps need to be done at the indicated times to achieve the desh-ed resu[t. Be sure to do each task as indicated. If a procedure or step is [eft out or not performed completely, cloning may not work. At each step, pay attention to assure the TV screen shows the proper message when cloning. If the message indicated does not appear, there is a problem with that step and cloning may not be successful C[oning is only possible when the signal source is an Analog channel, not a digita[ channel. Making a Master TV Detailed Instructions The following describes the procedure for preparing a Master L26W58HA for cloning and the procedure for adding Channel Icons and/or Labels. Note 1: Disconnect all Aux inputs. Under certain conditions, Auto Program Scan is disabled if there is an Aux input active. Note 2t Under certain conditions, changes to the input mode of the RGB inputs wilt not take effect until the power is cycled (TV is turned Off and On). To avoid confusion, disconnect a[L RGB inputs before entering the InstaUer menu. 1. Enter the L26W58HA installer menu. a. Reset the internal controller to factory default by accessing installer menu item 117 FACT DEFAULT,set it to 1 and press "ENTER". The value will change back to 0 after the TV's internal controller has been restored to factory default condition. b. Within the Installer menu, set the Installer menu items to the configuration required of your institution. c. It is important to set the tuning band at this time, see Insta[Ler menu item 03 BAND/AFC. d. Set Installer menu item 28 = CH OVERIDEto 001 to allow access to the Auto Program and Channel List!Channel Label features in the Channel Menu. Exit the Installer menu. 2. Access the Master TV menus and set the cLonabLe options on the menus to the desired configuration. Refer to the C{onabte Menu Features Chart on see page 52. 3. Run Auto Program. 4. Enter the Channel List/Channel Label menu and edit the channel Line-up to include the Free-To-Guest Channels only. 5. Assign ICONs to the channels using the Channel Label F4enu. Note: You can add Channel ICONStypicaUy network [ogos Like ABC, NBC, PBS etc. in this step. Oi, in Step 7, add Channel ICONS or [abels for channels without Icons. 6. Transfer the TV setup: Enter the L26W58HA instaLLer menu. Press '2', '5', '5', 'MENU' Lo sLarL Lhe hansFer or Ltle TV's seLup Lo the L26W58HA. Once the transfer is complete, the system will exit the Installer menu. Note: OnLy do 2-5-5 + MENU once. The TV setup may be corrupted if 255 + Menu is done more than one time. 7. Edit!Add Channel ICONs and Channel Labels as needed. Enter InstaUer menu. With menu displayed, press 2-5-4 + MENU. See page 52 for detai[ed instructions: - Editing/Adding Channel ICON and Labels on Master TV - Changing a Channel's ICON on Master IV - Changing/Adding Channel Labels on Master IV - Changing Source Labels on Master TV 8. Verify Master TV setup and feature configuration: • Did you add Channel ICONS? • Did you add Channel Labels? • Did you add Aux Source Labels? • Did you adjust all TV menu options as required? The TV master setup is now ready to be cloned. Go to the master TV cloning section or continue on to page 55. PAGE 54