LG TD-V10021G User Guide - Page 15

The Dryer Vent Location

Get LG TD-V10021G PDF manuals and user guides View all LG TD-V10021G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

INSTALLATIONINSTRUCTIONS CHANGING THE DRYER VENT LOCATION WARNING • Use a heavy metal vent. • Do not use plastic or thin foil duct. • Clean old ducts before installing this dryer. • Wear gloves during installation. • Failure to follow these instructions can result in death or fire. Your new dryer is shipped to vent to the rear. it can also be configured to vent to the bottom or side (right-side venting is not available on gas models). An adapter kit, part number 383EEL9001B, may be purchased from your LG retailer. This kit contains the necessary duct components to change the dryer vent location. Retaining Screw Rear Exhaust Duct Remove the rear exhaust duct retaining screw. Pull out the exhaust duct. OPTION 2: BOttOm / I Adapter Duct _, venting Bracket Knockout Pressthe tabs on the knockoutand carefullyremovethe knockoutfor the desiredvent opening(right-sideventing is not availableon gas models).Pressthe adapterduct ontothe blowerhousingand secureto the baseof the dryerasshown. Bracket Press the adapter duct onto the blower housing and secure to the base of the dryer as shown. Preassemblae4-in.(10cm)elbowto thenext4-in.(10cm) ductsection,andsecurealljointswith ducttape.Be sure that the maleendof theelbowfacesAWAYfromthe dryer. Inserttheelbow/ductassemblythroughthe sideopening andpressit ontotheadapterduct.Securein placewith ducttape. Besurethat themaleendof theduct protrudes11/i2n. (3.8 cm)to connecttheremainingductwork. Attachcoverplateto thebackof thedryerwith included screw. Cover Plate _J insert the 4-in. (10 cm) elbow through the rear opening and press it onto the adapter duct. Be sure that the male end of the elbow faces down through hole in the bottom of the dryer. Secure in place with duct tape. Attach the cover plate to the back of the dryer with included screw. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
INSTALLATION
INSTRUCTIONS
CHANGING
THE DRYER VENT LOCATION
WARNING
• Use a heavy metal vent.
• Do not use plastic or thin foil duct.
• Clean old ducts before installing this dryer.
• Wear gloves during installation.
• Failure to follow these instructions can result in death
or fire.
Your new dryer
is
shipped to vent to the rear.
it can also be configured
to vent to the bottom
or side (right-side
venting
is not available on
gas models).
An adapter
kit, part number 383EEL9001B,
may be purchased
from your
LG retailer. This
kit contains
the necessary
duct components
to change the dryer vent location.
Retaining
Screw
Rear
Exhaust
Duct
Remove the rear exhaust duct
retaining
screw. Pull out the exhaust duct.
Bracket
Knockout
Pressthe tabsonthe knockoutandcarefullyremovethe
knockoutforthedesiredventopening(right-sideventing
isnotavailableongasmodels).Presstheadapterduct
ontothe blowerhousingandsecureto the baseof the
dryerasshown.
Preassemble
a4-in.(10cm)elbowtothenext4-in.(10cm)
ductsection,andsecurealljointswithducttape.Besure
thatthe maleendof theelbowfacesAWAY
fromthe dryer.
Inserttheelbow/ductassembly
through
the sideopening
andpressitontotheadapterduct.Secure
inplacewith
ducttape.
Besurethatthemaleendof theductprotrudes11/2
in. (3.8
cm)toconnecttheremainingductwork.
Attachcoverplateto thebackof thedryerwithincluded
screw.
OPTION
2:
BOttOm
venting
/
I Adapter
Duct _,
Bracket
Press the adapter duct onto the blower
housing and secure to the base of the dryer
as shown.
Cover
Plate
_J
insert the 4-in. (10 cm) elbow through the
rear opening
and press it onto the adapter
duct. Be sure that the male end of the elbow
faces down through hole in the bottom of the
dryer. Secure in place with duct tape.
Attach the cover plate to the back of the
dryer with included
screw.
15