Lantronix SISPM1040-3166-L Installation Guide Rev G - Page 38

Initial Switch Configuration, Initial Switch Configuration via Web Browser

Get Lantronix SISPM1040-3166-L PDF manuals and user guides View all Lantronix SISPM1040-3166-L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Lantronix SISPM1040-3xxx-L Install Guide Chapter 3 - Initial Switch Configuration Initial Switch Configuration via Web Browser After powering up the switch for the first time, you can perform the initial switch configuration using a web browser. For managing other switch features, see the Web User Guide for details. To begin the initial configuration stage, you must reconfigure your PC's IP address and subnet mask so as to make sure the PC can communicate with the switch. After changing PC's IP address (for example, 192.168.1.250), then you can access the Web interface of the switch using the switch's default IP address as described below. Note: The switch factory default IP address is 192.168.1.77. The switch factory default Subnet Mask is 255.255.255.0. 1. Power up the PC that you will use for the initial configuration. Please make sure the PC has the Ethernet RJ45 connector to be connected to the switch via standard Ethernet LAN cable. 2. Reconfigure the PC's IP address and Subnet Mask as below, so that it can communicate with the switch. The method to change the PC's IP address (e.g., for a PC running Windows® 7/8.x/10) is as follows: 2a: Type "network and sharing" into the Search box in the Start Menu. 2b: Select Network and Sharing Center. 2c: Click on Change adapter settings on the left of PC screen. Note: You can skip step 2a to 2c, by pressing WinKey+R and type "ncpa.cpl" command to get to step 2d directly. 2d: Right-click on your local adapter and select Properties 2e: In the Local Area Connection Properties window highlight Internet Protocol Version 4 (TCP/IPv4) then click the Properties button. Note: Be sure to record all your PC's current IP settings to be able to restore them later. 2f: Select the radio button Use the following IP address and enter in the IP for the PC (e.g., any IP address not in use, and in between 192.168.1.2 and 192.168.1.254), Subnet mask (e.g., 255.255.255.0), and Default gateway that corresponds with your network setup. Then enter your Preferred and Alternate DNS server addresses. 2g: Click OK to change the PC's IP address. 3. Power up the switch to be initially configured and wait until it has finished its start-up processes. 4. Connect the PC to any port on the switch using a standard Ethernet cable, and check the port LED on the switch to make sure the link status of the PC is OK. 5. Run your Web browser on the PC; enter the factory default IP address to access the switch's Web interface. 33762 Rev. G https://www.lantronix.com/ Page 38 of 48

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Lantronix
SISPM1040-3xxx-L Install Guide
33762 Rev. G
Page
38
of
48
Chapter 3 - Initial Switch Configuration
Initial Switch Configuration via Web Browser
After powering up the switch for the first time, you can perform the initial switch configuration using a web
browser. For managing other switch features, see the
Web User Guide
for details.
To begin the initial configuration stage, you must reconfigure your PC’s IP address and subnet mask so as to make
sure the PC can communicate with the switch. After changing PC’s IP address (for example, 192.168.1.250), then
you can access the Web interface of the switch using the switch’s default IP address as described below.
Note
: The switch factory default IP address is 192.168.1.77. The switch factory default Subnet Mask is
255.255.255.0.
1.
Power up the PC that you will use for the initial configuration. Please make sure the PC has the Ethernet RJ45
connector to be connected to the switch via standard Ethernet LAN cable.
2.
Reconfigure the PC’s IP address and Subnet Mask as below, so that it can communicate with the switch.
The method to change the PC’s IP address (e.g., for a PC running Windows® 7/8.x/10) is as follows:
2a: Type “network and sharing“ into the Search box in the Start Menu.
2b: Select Network and Sharing Center.
2c: Click on
Change adapter settings
on the left of PC screen.
Note
: You can skip step 2a to 2c, by pressing WinKey+R and type ”ncpa.cpl” command to get to step 2d directly.
2d: Right-click on your local adapter and select Properties
2e: In the Local Area Connection Properties window highlight Internet Protocol Version 4 (TCP/IPv4) then click
the Properties button.
Note
: Be sure to record all your PC’s current IP settings to be able to restore them later.
2f: Select the radio button
Use the following IP addres
s and enter in the IP for the PC (e.g., any IP address not
in use, and in between 192.168.1.2 and 192.168.1.254), Subnet mask (e.g., 255.255.255.0), and Default
gateway that corresponds with your network setup. Then enter your Preferred and Alternate DNS server
addresses.
2g: Click
OK
to change the PC’s IP address.
3.
Power up the switch to be initially configured and wait until it has finished its start-up processes.
4.
Connect the PC to any port on the switch using a standard Ethernet cable, and check the port LED on the switch
to make sure the link status of the PC is OK.
5.
Run your Web browser on the PC; enter the factory default IP address to access the switch’s Web interface.