Lenovo S50-30 (English) User Guide - Lenovo S50-30 - Page 40

Removing the computer cover

Get Lenovo S50-30 PDF manuals and user guides View all Lenovo S50-30 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

7. Tighten the two screws to secure the monitor stand to the computer. Then, put the rubber blocks into the holes to protect the screws. Removing the computer cover Attention: Do not remove the computer cover or attempt any repairs before reading the "Important safety information" in the Safety and Warranty Guide that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support Web site at: http://support.lenovo.com CAUTION: Turn off the computer and wait three to five minutes to let the computer cool down before removing the cover. This section provides instructions on how to remove the computer cover. To remove the computer cover, do the following. 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Place a soft, clean towel or cloth on the desk or other flat surface. Hold the sides of your computer and gently lay it down so that the screen is resting on the towel or cloth and the cover is facing up. 3. Remove any locking device that secures the computer cover. 4. Remove the computer stand. See "Removing and reattaching the frame stand", "Removing and reattaching the monitor stand", or "Removing and reattaching the transformer stand". User Guide 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
35
User Guide
7.
Tighten the two screws to secure the monitor stand to the computer. Then, put
the rubber blocks into the holes to protect the screws.
Removing the computer cover
Attention:
Do not remove the computer cover or attempt any repairs
before reading the “Important safety information” in the
Safety and
Warranty Guide
that was included with your computer or in the
Hardware
Maintenance Manual
(HMM) for the computer. To obtain copies of the
Safety and Warranty Guide
or
HMM
, go to the Support Web site at:
CAUTION:
Turn off the computer and wait three to five minutes to let the computer
cool down before removing the cover.
This section provides instructions on how to remove the computer cover.
To remove the computer cover, do the following.
1.
Remove all media from the drives and turn off all attached devices and the
computer. Then, disconnect all power cords from electrical outlets and
disconnect all cables that are connected to the computer.
2.
Place a soft, clean towel or cloth on the desk or other flat surface. Hold the
sides of your computer and gently lay it down so that the screen is resting on
the towel or cloth and the cover is facing up.
3.
Remove any locking device that secures the computer cover.
4.
Remove the computer stand. See “Removing and reattaching the frame stand”,
“Removing and reattaching the monitor stand”, or “Removing and reattaching
the transformer stand”.